- 您现在的位置：买卖IC网 > PDF目录19847 > NCP1377BDR2G (ON Semiconductor)IC CTRLR PWM SMPS CM UVLO 8SOIC PDF资料下载
参数资料
| 型号： | NCP1377BDR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SMPS CM UVLO 8SOIC |
| 标准包装： | 1 |
| 输出隔离： | 隔离 |
| 频率范围： | 300kHz |
| 输入电压： | 8.2 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 标准包装 |
| 其它名称： | NCP1377BDR2GOSDKR |
NCP1377, NCP1377B
Once the power supply has started, the V CC shall be
constrained below 16 V, which is the maximum rating on
pin 6. Figure 17 portrays a typical NCP1377 startup
sequence with a Vcc regulated at 12.5 V.
13.5
Skipping Cycle Mode
The NCP1377 automatically skips switching cycles
when the output power demand drops below a given level.
This is accomplished by monitoring the FB pin. In normal
operation, pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
12.5
11.5
12.5 V
Regulation
determined level, the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the so ? called skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 18)
and follows the following formula:
1 · Lp · Ip2 · Fsw · D burst with:
10.5
9.50
Figure 17. A Typical Startup Sequence
for the NCP1377
2
Lp = Primary inductance
Fsw = Switching frequency within the burst
Ip = Peak current at which skip cycle occurs
D burst = Burst width/burst recurrence
300
MAX PEAK
CURRENT
NORMAL CURRENT
MODE OPERATION
DRIVER
DRIVER = HIGH ? I = 0
DRIVER = LOW ? I = 200 m A
200
100
SKIP CYCLE
CURRENT LIMIT
RESET
-
+
3
2
R skip
R sense
0
WIDTH
RECURRENCE
Figure 18. The Skip Cycle Takes Place at Low Peak
Currents which Guarantees Noise ? Free Operation
The skip level selection is done through a simple resistor
inserted between the current sense input and the sense
element. Everytime the NCP1377 output driver goes low,
a 200 m A source forces a current to flow through the sense
pin (Figure 19): when the driver is high, the current source
is off and the current sense information is normally
processed. As soon as the driver goes low, the current
source delivers 200 m A and develops a ground referenced
voltage across Rskip. If this voltage is below the feedback
voltage, the current sense comparator stays in the low state
and the internal latch can be triggered by the next clock
cycle. Now, if because of a low load mode the feedback
+
Figure 19. A Patented Method Allows for Skip
Level Selection via a Series Resistor Inserted in
Series with the Current
voltage is below Rskip level, then the current sense
comparator permanently resets the latch and the next clock
cycle (given by the demagnetization detection) is ignored:
we are skipping cycles as shown by Figure 18. As soon as
the feedback voltage goes up again, there can be two
situations: the recurrent period is small and a new
demagnetization detection (next wave) signal triggers the
NCP1377. To the opposite, in low output power conditions,
no more ringing waves are present on the drain and the
toggling of the current sense comparator alone initiates a
new cycle start. Figure 20 depicts these two different
situations.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BW0-CY-F3 | CONVERTER MOD DC/DC 5V 50W |
| EPM570M100C5N | IC MAX II CPLD 570 LE 100-MBGA |
| VE-BW0-CY-F2 | CONVERTER MOD DC/DC 5V 50W |
| EPM570T100C5N | IC MAX II CPLD 570 LE 100-TQFP |
| VE-BW0-CY-F1 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1377BDR2G-CUT TAPE | 制造商:ON 功能描述:NCP1377 Series 18 V 300 kHz Surface Mount PWM Current-Mode Controller - SOIC-8 |
| NCP1377BP | 功能描述:电流型 PWM 控制器 Quasi Resonant RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377BPG | 功能描述:电流型 PWM 控制器 Quasi Resonant Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377D1R2G | 功能描述:电流型 PWM 控制器 Quasi Resonant Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377DR2 | 功能描述:开关变换器、稳压器与控制器 Quasi Resonant RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。