- 您现在的位置：买卖IC网 > PDF目录15221 > NCP1395ADR2G (ON Semiconductor)IC REG CTRLR PWM VM 16-SOIC PDF资料下载
参数资料
| 型号： | NCP1395ADR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM VM 16-SOIC |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 1.11MHz |
| 占空比： | 52% |
| 电源电压： | 9.3 V ~ 20 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP1395ADR2GOSCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页
NCP1395A/B
In this figure, the internal OPAMP is used to perform a
kind of constant current operation (CC) by taking the lead
when the other voltage loop is gone (CV). Due to the ORing
capability on the FB pin, the OPAMP regulates in constant
current mode. When the output reaches a low level close to
a complete short ? circuit, the OPAMP output is maximum.
With a resistive divider on the slow fault, this condition can
be detected to trigger the delayed fault. If no OPAMP shall
be used, its input must be grounded.
Slow Input
On this circuit, the slow input goes to a comparator.
When this input exceeds 1.0 V typical, the current source
Itimer turns on, charging the external capacitor Ctimer. If
the fault duration is long enough, when Ctimer voltage
reaches the VtimerON level (4.0 V typical), then all pulses
are stopped. Itimer turns off and the capacitor slowly
discharges to ground via a resistor installed in parallel with
it. As a result, the designer can easily determine the time
during which the power supply stays locked by playing on
Rtimer. Now, when the timer capacitor voltage reaches
1.0 V typical (VtimerOFF), the comparator instructs the
internal logic to issues pulses as on a clean soft ? start
sequence (soft ? start is activated). Please note that the
discharge resistor cannot be lower than 4.0 V/Itimer,
otherwise the voltage on Ctimer will never reach the
turn ? off voltage of 4.0 V.
In both cases, when the fault is validated, both outputs A
and B are internally pulled down to ground.
V CC
FB
Fast Fault
Figure 49. A resistor can easily program the capacitor discharge time.
Figure 50. Skip cycle can be
implemented via two
resistors on the FB pin to the
fast fault input.
Fast Input
The fast input is not affected by a delayed action. As soon
as its voltage exceeds 1.0 V typical, all pulses are off and
maintained off as long as the fault is present. When the pin
is released, pulses come back without soft ? start for the
A version, with soft ? start for the B version.
Due to the low activation level of 1.0 V, this pin can
observe the feedback pin via a resistive divided and thus
implement skip cycle operation. The resonant converter
can be designed to lose regulation in light load conditions,
forcing the FB level to increase. When it reaches the
programmed level, it triggers the fast fault input and stops
pulses. Then V out slowly drops, the loop reacts by
decreasing the feedback level which, in turn, unlocks the
pulses: Vout goes up again and so on: we are in skip cycle
mode.
Startup Behavior
When the V CC voltage grows up, the internal current
consumption is kept to Istup, allowing to crank up the
converter via a resistor connected to the bulk capacitor.
When V CC reaches the V CC ON level, output A goes high
first and then output B. This sequence will always be the
same, whatever triggers the pulse delivery: fault, OFF to
ON etc … Pulsing the output A high first gives an
immediate charge of the bootstrap capacitor when an
integrated high voltage half ? bridge driver is implemented
such as ON Semiconductor ’s NCP5181. Then, the rest of
pulses follow, delivered at the highest switching value, set
by the resistor on pin 2. The soft ? start capacitor ensures a
smooth frequency decrease to either the programmed
minimum value (in case of fault) or to a value
corresponding to the operating point if the feedback loop
closes first. Figure 51 shows typical signals evolution at
power on.
http://onsemi.com
23
相关PDF资料 |
PDF描述 |
|---|---|
| H2BXG-10110-B8-ND | JUMPER-H1501TR/A3048B/X 10" |
| LP122M050A1P3 | CAP ALUM 1200UF 50V 20% SNAP |
| GEA36DTMI | CONN EDGECARD 72POS R/A .125 SLD |
| GBA36DRMS | CONN EDGECARD 72POS .125 SQ WW |
| EBM25DTBT | CONN EDGECARD 50POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1395APG | 功能描述:电压模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1395B | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
| NCP1395BDR2G | 功能描述:电压模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1395BPG | 功能描述:电压模式 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1395D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Performance Resonant Mode Controller |
发布紧急采购，3分钟左右您将得到回复。