- 您现在的位置：买卖IC网 > PDF目录15054 > NCP1575DG (ON Semiconductor)IC REG CTRLR BUCK PWM 8-SOIC PDF资料下载
参数资料
| 型号： | NCP1575DG |
| 厂商： | ON Semiconductor |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 8-SOIC |
| 产品变化通告： | Product Obsolescence 08/Apr/2011 |
| 标准包装： | 98 |
| PWM 型： | 电流/电压模式，V²? |
| 输出数： | 1 |
| 频率 - 最大： | 320kHz |
| 电源电压： | 9 V ~ 20 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
NCP1575
In order to choose the minimum value of inductance, input
voltage, output voltage and output current must be known.
Most computer applications use reasonably well regulated
bulk power supplies so that, while the equations below
specify V IN(MAX) or V IN(MIN) , it is possible to use the
Inductor value selection also depends on how much output
ripple voltage the system can tolerate. Output ripple voltage
is defined as the product of the output ripple current and the
output filter capacitor ESR.
Thus, output ripple voltage can be calculated as:
nominal value of V IN in these calculations with little error.
Current in the inductor while operating in the continuous
current mode is defined as the load current plus ripple
VRIPPLE + ESRC IRIPPLE +
ESRC VIN * VOUT VOUT
fOSC L VIN
(VIN * VOUT)VOUT
IRIPPLE +
current.
IL + ILOAD ) IRIPPLE
The ripple current waveform is triangular, and the current
is a function of voltage across the inductor, switch FET
on?time and the inductor value. FET on?time can be defined
as the product of duty cycle and switch frequency, and duty
cycle can be defined as a ratio of V OUT to V IN . Thus,
(fOSC)(L)(VIN)
Peak inductor current is defined as the load current plus
half of the peak current. Peak current must be less than the
maximum rated FET switch current, and must also be less
than the inductor saturation current. Thus, the maximum
Finally, we should consider power dissipation in the
output inductors. Power dissipation is proportional to the
square of inductor current:
PD + (I 2L )(ESRL)
The temperature rise of the inductor relative to the air
surrounding it is defined as the product of power dissipation
and thermal resistance to ambient:
D T(inductor) + (Ra)(PD)
Ra for an inductor designed to conduct 20 A to 30 A is
approximately 45 ° C/W. The inductor temperature is given as:
T(inductor) + D T(inductor) ) Tambient
V CC Bypass Filtering
output current can be defined as:
IOUT(MAX) + ISWITCH(MAX) *
VIN(MAX) * VOUT VOUT
2 fOSC L VIN(MAX)
A small RC filter should be added between module V CC
and the V CC input to the IC. A 10 W resistor and a 0.47 m F
capacitor should be sufficient to ensure the controller IC does
Since the maximum output current must be less than the
maximum switch current, the minimum inductance required
can be determined.
not operate erratically due to injected noise, and will also
supply reserve charge for the onboard gate drivers.
Input Filter Capacitors
L(MIN) +
(VIN(MIN) * VOUT)VOUT
(fOSC)(ISWITCH(MAX))(VIN(MIN))
The input filter capacitors provide a charge reservoir that
minimizes supply voltage variations due to changes in current
This equation identifies the value of inductor that will
provide the full rated switch current as inductor ripple
flowing through the switch FETs. These capacitors must be
chosen primarily for ripple current rating.
current, and will usually result in inefficient system
operation. The system will sink current away from the load
during some portion of the duty cycle unless load current is
greater than half of the rated switch current. Some value
V IN
L IN
I IN(AVE)
C IN
L OUT
V OUT
C OUT
larger than the minimum inductance must be used to ensure
the converter does not sink current. Choosing larger values
of inductor will reduce the ripple current, and inductor value
can be designed to accommodate a particular value of ripple
I RMS(CIN)
CONTROL
INPUT
L(RIPPLE) +
(L)( D IOUT)
(VIN * VOUT)
IIN(AVE) + IOUT
current by replacing I SWITCH(MAX) with a desired value of
I RIPPLE :
(VIN(MIN) * VOUT)VOUT
(fOSC)(IRIPPLE)(VIN(MIN))
However, reducing the ripple current will cause transient
response times to increase. The response times for both
increasing and decreasing current steps are shown below.
TRESPONSE(INCREASING) +
Figure 23.
Consider the schematic shown in Figure 23. The average
current flowing in the input inductor L IN for any given
output current is:
VOUT
VIN
Input capacitor current is positive into the capacitor when
the switch FETs are off, and negative out of the capacitor
when the switch FETs are on. When the switches are off,
TRESPONSE(DECREASING) +
(L)( D IOUT)
(VOUT)
I IN(AVE) flows into the capacitor. When the switches are on,
capacitor current is equal to the per?phase output current
http://onsemi.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| DS1818R-5/T&R | IC ECONRST 3.3V W/PB 5% SOT23-3 |
| DS1818R-20/T&R | IC ECONRST 3.3V W/PB 20% SOT23-3 |
| DS1816R-20/T&R | IC ECONORST 3.3V O-D 20%SOT23-3 |
| HCC19DRXS | CONN EDGECARD 38POS DIP .100 SLD |
| NCP1575D | IC REG CTRLR BUCK PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1575DR2 | 功能描述:DC/DC 开关控制器 Low Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP1575DR2G | 功能描述:DC/DC 开关控制器 Low Voltage Synchronous Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP1578MNR2G | 功能描述:IC REG DL BCK/LINEAR SYNC 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| NCP1579DR2G | 功能描述:电压模式 PWM 控制器 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1580DR2 | 功能描述:电压模式 PWM 控制器 Low Voltage RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。