参数资料
型号: NCP1654BD133R2G
厂商: ON Semiconductor
文件页数: 5/23页
文件大小: 228K
描述: IC PFC CCM 133KHZ 8-SOIC
标准包装: 2,500
模式: 连续导电(CCM)
频率 - 开关: 120kHz ~ 146kHz
电流 - 启动: 75µA
电源电压: 9 V ~ 20 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOICN
包装: 带卷 (TR)
其它名称: NCP1654BD133R2G-ND
NCP1654BD133R2GOSTR
NCP1654
http://onsemi.com
5
DETAILED PIN DESCRIPTIONS
Pin
Symbol
Name
Function
1
GND
Ground

2
V
in
Multiplier
Voltage
This pin provides a voltage V
M
 for the PFC duty cycle modulation. The input impedance of the
PFC circuits is proportional to the resistor R
M
 externally connected to this pin. The device op-
erates in average current mode if an external capacitor C
M
 is connected to the pin. Otherwise,
it operates in peak current mode.
3
CS
Current Sense
Input
This pin sources a current I
CS
 which is proportional to the inductor current I
L
. The sense cur-
rent I
CS
 is for overcurrent protection (OCP), overpower limitation (OPL) and PFC duty cycle
modulation. When I
CS
 goes above 200 mA, OCP is activated and the Drive Output is disabled.
4
V
BO
BrownOut / In
Connect a resistor network among the rectified input voltage, BO pin, and ground. And connect
a capacitor between BO pin and ground. BO pin detects a voltage signal proportional to the
average input voltage.
When V
BO
 goes below V
BOL
, the circuit that detects too low input voltage conditions (brown
out), turns off the output driver and keeps it in low state until V
BO
 exceeds V
BOH
.
This signal which is proportional to the RMS input voltage V
ac
 is also for overpower limitation
(OPL) and PFC duty cycle modulation.
5
V
control
Control Voltage /
SoftStart
The voltage of this pin V
control
 directly controls the input impedance. This pin is connected to
external type2 compensation components to limit the V
control
 bandwidth typically below 20 Hz
to achieve near unity power factor.
The device provides no output when V
control
 < V
control(min)
. When it starts operation, the power
increases slowly (softstart).
6
V
FB
FeedBack /
Shutdown
This pin receives a feedback signal V
FB
 that is proportional to the PFC circuits output voltage.
This information is used for both the output regulation, the overvoltage protection (OVP), and
output undervoltage protection (UVP) to protect the system from damage at feedback abnor-
mal situation.
When V
FB
 goes above 105% V
REF
, OVP is activated and the Drive Output is disabled.
When V
FB
 goes below 8% V
REF
, the device enters a lowconsumption shutdown mode.
7
V
CC
Supply Voltage
This pin is the positive supply of the IC. The circuit typically starts to operate when V
CC
 ex-
ceeds 10.5 V and turns off when V
CC
 goes below 9 V. After startup, the operating range is 9 V
up to 20 V.
8
DRV
Drive Output
The high current capability of the totem pole gate drive (?.5 A) makes it suitable to effectively
drive high gate charge power MOSFET.
相关PDF资料
PDF描述
NCP1927DR2G IC CTLR PFC/FLYBACK 16-SOIC
NCP380HMU21AATBG IC CURRENT LIMIT SWITCH 6-UDFN
NCT1008DMT3R2G TMP DIO MON/SMBUS 4CH 8WDFN
NCT210RQR2G IC TEMP SENSOR LOC/REM 16QSOP
NCT214MT3R2G IC TEMP SENSOR LOC/REM 10WDFN
相关代理商/技术参数
参数描述
NCP1654BD200R2G 功能描述:功率因数校正 IC NCP1654 - 200KHZ RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1654BD65R2G 功能描述:功率因数校正 IC NCP1654-65K-B-SOIC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1654BP65G 功能描述:功率因数校正 IC NCP1654-65K-B-PDIP RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1654PFCGEVB 功能描述:电源管理IC开发工具 NCP1654 PWR FACT CONT EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP1729-SKT 制造商:P&S 功能描述:Sample Kit, including Two NCP1729SN35T1 and A Development Source CD-ROM 制造商:P&S 功能描述:Sample Kit,including Two NCP1729SN35T1 and A Development Source CD-ROM