参数资料
| 型号： | NCP3020BDR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 17/23页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 8-SOIC |
| 标准包装： | 1 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 670kHz |
| 占空比： | 80% |
| 电源电压： | 4.7 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 其它名称： | NCP3020BDR2GOSDKR |
NCP3020A, NCP3020B, NCV3020A, NCV3020B
16 V out = 3.3 V
15
12 V
9V
I PP +
LP CU + I RMS 2 @ DCR
1 ) ra 3 10.02 A
I RMS + I OUT @
12
+ 10 A @
1 )
18
17
18 V
14
13 15 V
12
11
10
9
8
7
6
5
4
3
2
1
0
10% 15% 20% 25% 30% 35% 40%
V IN , (V)
Figure 32. Ripple Current Ratio vs. Inductance
To keep within the bounds of the parts maximum rating,
calculate the RMS current and peak current.
2
(eq. 8)
(0.24) 2
12
V OUT (1 * D)
(eq. 11)
L OUT @ F SW
Ipp is the peak to peak current of the inductor. From this
equation it is clear that the ripple current increases as L OUT
decreases, emphasizing the trade ? off between dynamic
response and ripple current.
The power dissipation of an inductor consists of both
copper and core losses. The copper losses can be further
categorized into dc losses and ac losses. A good first order
approximation of the inductor losses can be made using the
DC resistance as they usually contribute to 90% of the losses
of the inductor shown below:
(eq. 12)
The core losses and ac copper losses will depend on the
geometry of the selected core, core material, and wire used.
Most vendors will provide the appropriate information to
make accurate calculations of the power dissipation then the
total inductor losses can be capture buy the equation below:
LP tot + LP CU_DC ) LP CU_AC ) LP Core (eq. 13)
Input Capacitor Selection
The input capacitor has to sustain the ripple current
I PK + I OUT @ 1 )
ra
2
3 11.2 A + 10 A @ 1 )
(0.24)
2
(eq. 9)
produced during the on time of the upper MOSFET, so it
must have a low ESR to minimize the losses. The RMS value
of this ripple is:
SlewRate LOUT + 3 2.6 +
L OUT
(eq. 15)
I INRUSH +
An inductor for this example would be around 3.3 m H and
should support an rms current of 10.02 A and a peak current
of 11.2 A.
The final selection of an output inductor has both
mechanical and electrical considerations. From a
mechanical perspective, smaller inductor values generally
correspond to smaller physical size. Since the inductor is
often one of the largest components in the regulation system,
a minimum inductor value is particularly important in
space ? constrained applications. From an electrical
perspective, the maximum current slew rate through the
output inductor for a buck regulator is given by Equation 10.
V IN * V OUT A 12 V * 3.3 V
m s 3.3 m H
(eq. 10)
This equation implies that larger inductor values limit the
regulator ’s ability to slew current through the output
inductor in response to output load transients. Consequently,
output capacitors must supply the load current until the
inductor current reaches the output load current level. This
results in larger values of output capacitance to maintain
tight output voltage regulation. In contrast, smaller values of
inductance increase the regulator ’s maximum achievable
slew rate and decrease the necessary capacitance, at the
expense of higher ripple current. The peak ? to ? peak ripple
current for the NCP3020A is given by the following
Iin RMS + I OUT @ D @ (1 * D) (eq. 14)
D is the duty cycle, Iin RMS is the input RMS current, and
I OUT is the load current.
The equation reaches its maximum value with D = 0.5.
Loss in the input capacitors can be calculated with the
following equation:
2
P CIN + ESR CIN @ I IN * RMS
P CIN is the power loss in the input capacitors and ESR CIN
is the effective series resistance of the input capacitance.
Due to large dI/dt through the input capacitors, electrolytic
or ceramics should be used. If a tantalum must be used, it
must by surge protected. Otherwise, capacitor failure could
occur.
Input Start ? up Current
To calculate the input startup current, the following
equation can be used.
C OUT @ V OUT
(eq. 16)
t SS
I inrush is the input current during startup, C OUT is the total
output capacitance, V OUT is the desired output voltage, and
t SS is the soft start interval. If the inrush current is higher than
the steady state input current during max load, then the input
fuse should be rated accordingly, if one is used.
equation:
http://onsemi.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| NCP304ALSQ43T1G | IC VOLT DETECTOR 4.3V SC-82AB |
| NCP305LSQ49T1 | IC VOLT DETECT OD 4.9V SC-82AB |
| NCP3101CMNTXG | IC REG BUCK SYNC ADJ 6A 40QFN |
| NCP3120MNTXG | IC REG BUCK ADJ 2A DL 32QFN |
| NCP3121MNTXG | IC REG BUCK ADJ 3A DL 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP3020BGEVB | 功能描述:电源管理IC开发工具 NCP3020A EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP302HSN09T1 | 功能描述:电压监测器/监控器 0.9V Detector RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCP302HSN09T1G | 功能描述:电压监测器/监控器 0.9V Detector w/Reset Hgh RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| NCP302HSN15T1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| NCP302HSN18T1 | 功能描述:电压监测器/监控器 1.8V Detector RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。