参数资料
| 型号： | NCP3126ADR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/23页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.8V |
| 输入电压： | 4.5 V ~ 13.2 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 350kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SOICN |
| 其它名称： | NCP3126ADR2GOSDKR |
NCP3126
when using electrolytic capacitors, a lower ripple current
will result in lower output ripple due to the higher ESR of
electrolytic capacitors. The ratio of ripple current to
maximum output current is given in Equation 5.
I OUT = Output current
I PK = Inductor peak current
ra = Ripple current ratio
A standard inductor should be found so the inductor will
ra + D I 3 28% +
Iout
0.84 A
3A
(eq. 5)
be rounded to 6.8 m H. The inductor should also support an
RMS current of 3.01 A and a peak current of 3.42 A.
The final selection of an output inductor has both
L OUT +
V OUT
I OUT @ ra @ F SW
6.73 m H +
@ (1 * 27.5%)
SlewRate LOUT + 3 1.41
L OUT
D I = Ripple current
I OUT = Output current
ra = Ripple current ratio
Using the ripple current rule of thumb, the user can
establish acceptable values of inductance for a design using
Equation 6.
@ (1 * D) 3
(eq. 6)
3.3 V
3 A @ 28% @ 350 kHz
D = Duty ratio
F SW = Switching frequency
I OUT = Output current
L OUT = Output inductance
ra = Ripple current ratio
20
mechanical and electrical considerations. From a
mechanical perspective, smaller inductor values generally
correspond to smaller physical size. Since the inductor is
often one of the largest components in the regulation system,
a minimum inductor value is particularly important in space
constrained applications. From an electrical perspective, the
maximum current slew rate through the output inductor for
a buck regulator is given by Equation 9.
V IN * V OUT A
m s
(eq. 9)
12 V * 3.3 V
+
6.8 m H
L OUT = Output inductance
V IN = Input voltage
V OUT = Maximum output voltage
Equation 9 implies that larger inductor values limit the
regulator ’s ability to slew current through the output
18
16
14
12
10
V IN = 12 V
inductor in response to output load transients. Consequently,
output capacitors must supply the load current until the
inductor current reaches the output load current level.
Reduced inductance to increase slew rates results in larger
values of output capacitance to maintain tight output voltage
regulation. In contrast, smaller values of inductance increase
the regulator ’s maximum achievable slew rate and decrease
Selected
V IN = 8 V
V IN = 4.2 V
V OUT (1 * D)
L OUT @ F SW
0.84 A +
8
6
4
2
10 13 16 19 22 25 28 31 34 37
CURRENT RIPPLE RATIO (%)
Figure 21. Inductance vs. Current Ripple Ratio
40
the necessary capacitance, at the expense of higher ripple
current. The peak ? to ? peak ripple current for NCP3126 is
given by the following equation:
Ipp + 3
(eq. 10)
3.3 V (1 * 27.5%)
6.8 m H @ 350 kHz
1 ) ra 3
I RMS + I OUT @
12
3.01 A + 3 A * 1 )
I PK + I OUT @ 1 )
3 3.42 A + 3 A @ 1 )
When selecting an inductor, the designer must not exceed
the current rating of the part. To keep within the bounds of
the part’s maximum rating, a calculation of the RMS and
peak inductor current is required.
2
(eq. 7)
28% 2
12
I OUT = Output current
I RMS = Inductor RMS current
ra = Ripple current ratio
ra 28%
2 2
(eq. 8)
D = Duty ratio
F SW = Switching frequency
Ipp = Peak ? to ? peak current of the inductor
L OUT = Output inductance
V OUT = Output voltage
From Equation 10 it is clear that the ripple current increases
as L OUT decreases, emphasizing the trade ? off between
dynamic response and ripple current.
The power dissipation of an inductor falls into two
categories: copper and core losses. The copper losses can be
further categorized into DC losses and AC losses. A good
first order approximation of the inductor losses can be made
using the DC resistance as shown below:
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| NCP3127ADR2G | IC REG BUCK SYNC ADJ 2A 8SOIC |
| NCP3218GMNR2G | IC CTLR CPU SYNC BUCK 7BIT 48QFN |
| NCP330MUTBG | IC LOAD SWITCH FET 3A 4UDFN |
| NCP3520DMR2G | IC REG LDO 1.2V 3A MICRO8 |
| NCP362CMUTBG | IC OCP TVS ESD USB POS 10-UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP3126AGEVB | 功能描述:电源管理IC开发工具 NCP3126 EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3126CRAGEVB | 功能描述:电源管理IC开发工具 NCP3126 CERAMIC EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3127ADR2G | 功能描述:直流/直流开关转换器 2A PWM Switching Buck Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP3127AGEVB | 功能描述:电源管理IC开发工具 NCP3127 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3127CRAGEVB | 功能描述:电源管理IC开发工具 NCP3127 CERAMIC EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。