参数资料
| 型号： | NCP5381AMNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 24/34页 |
| 文件大小： | 0K |
| 描述： | IC BUCK CTLR 2/3/4PHASE 40-QFN |
| 产品变化通告： | Specification Change MSL Updated 13/June/2008 Product Discontinuation 01/Oct/2008 |
| 标准包装： | 2,500 |
| 应用： | 控制器，Intel Pentium? IV |
| 输入电压： | 10.8 V ~ 13.2 V |
| 输出数： | 4 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
NCP5381A
FUNCTIONAL DESCRIPTION
General
The NCP5381A dual edge modulated multiphase PWM
controller is specifically designed with the necessary
shown in the 4-- phase Applications Schematic. The
following truth table summarizes the modes of operation:
features for a high current VR10 or VR11 CPU power
system. The IC consists of the following blocks: Precision
Programmable DAC, Differential Remote Voltage Sense
Amplifier, High Performance Voltage Error Amplifier,
Mode
2--Phase
G1
Normal
Gate Output Connections
G2 G3
OPEN Normal
G4
OPEN
Differential Current Feedback Amplifiers, Precision
Oscillator and Triangle Wave Generators, and PWM
Comparators. Protection features include Undervoltage
3--Phase
4--Phase
Normal
Normal
Normal
Normal
Normal
Normal
GND
Normal
Lockout, Soft-- Start, Overcurrent Protection, Overvoltage
Protection, and Power Good Monitor.
Remote Output Sensing Amplifier (RSA)
A true differential amplifier allows the NCP5381A to
measure Vcore voltage feedback with respect to the Vcore
ground reference point by connecting the Vcore reference
point to VS+, and the Vcore ground reference point to VS-- .
This configuration keeps ground potential differences
between the local controller ground and the Vcore ground
reference point from affecting regulation of Vcore between
Vcore and Vcore ground reference points. The RSA also
subtracts the DAC (minus VID offset) voltage, thereby
producing an unamplified output error voltage at the
DIFFOUT pin. This output also has a 1.3 V bias voltage to
allow both positive and negative error voltages.
Precision Programmable DAC
A precision programmable DAC is provided. This DAC
has 0.5% accuracy over the entire operating temperature
range of the part. The DAC can be programmed to support
either VR10 or VR11 specifications. A program selection pin
is provided to accomplish this. This pin also sets the startup
mode of operation. Connect this pin to 1.25 V to select the
VR11 DAC table, and the VR11 startup mode. Connect this
pin to ground to select the VR10 DAC table and the VR11
startup mode. Connect this pin to VREF to select the VR10
DAC table and the VR10 startup mode.
High Performance Voltage Error Amplifier
The error amplifier is designed to provide high slew rate
and bandwidth. Although not required when operating as
a voltage regulator for VR10 or VR11, a capacitor from
COMP to VFB is required for stable unity gain test
configurations.
Gate Driver Outputs and 2/3/4 Phase Operation
The part can be configured to run in 2-- , 3-- , or 4-- phase
mode. In 2-- phase mode, phases 1 and 3 should be used to
drive the external gate drivers as shown in the 2-- phase
Applications Schematic. In 3-- phase mode, gate output G4
must be grounded as shown in the 3-- phase Applications
Schematic. In 4-- phase mode all 4 gate outputs are used as
These are the only allowable connection schemes to
program the modes of operation.
Differential Current Sense Amplifiers
Four differential amplifiers are provided to sense the
output current of each phase. The inputs of each current
sense amplifier must be connected across the current
sensing element of the phase controlled by the
corresponding gate output (G1, G2, G3, or G4). If a phase
is unused, the differential inputs to that phase’s current
sense amplifier must be shorted together and connected
to V CCP as shown in the 2-- and 3-- phase Application
Schematics .
A voltage is generated across the current sense element
(such as an inductor or sense resistor) by the current
flowing in that phase. The output of the current sense
amplifiers are used to control three functions. First, the
output controls the adaptive voltage positioning, where the
output voltage is actively controlled according to the
output current. In this function, all of the current sense
outputs are summed so that the total output current is used
for output voltage positioning. Second, the output signal is
fed to the current limit circuit. This again is the summed
current of all phases in operation. Finally, the individual
phase current is connected to the PWM comparator. In this
way current balance is accomplished.
Oscillator and Triangle Wave Generator
A programmable precision oscillator is provided. The
oscillator ’s frequency is programmed by the resistance
connected from the ROSC pin to ground. The user will
usually form this resistance from two resistors in order to
create a voltage divider that uses the ROSC output voltage
as the reference for creating the current limit setpoint
voltage. The oscillator frequency range is 100 kHz/phase
to 1.0 MHz/phase. The oscillator generates up to 4 triangle
waveforms (symmetrical rising and falling slopes)
between 1.3 V and 2.3 V. The triangle waves have a phase
delay between them such that for 2-- , 3-- , and 4-- phase
operation the PWM outputs are separated by 180, 120, and
90 angular degrees, respectively.
http://onsemi.com
24
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5381MNR2G | IC CTLR BUCK 2/3/4PHASE 40-QFN |
| NCP5382MNR2G | IC BUCK CTLR 2-6PHASE 48-QFN |
| NCP5383MNR2G | IC REG CTRLR BUCK PWM 24-QFN |
| NCP5385MNR2G | IC CTLR BUCK 2/3/4PHASE 40-QFN |
| NCP5386BMNR2G | IC CTLR BUCK 1/2PHASE 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5381MNR2G | 功能描述:DC/DC 开关控制器 ANA 2/3/4 PHSE BUCK CNTLR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5382 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2/3/4/5/6 Phase Buck Controller for VR10 and VR11 Pentium IV Processor Applications |
| NCP5382MNR2G | 功能描述:DC/DC 开关控制器 PHASE CONTROLLER 4 5 6 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5383 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2 Phase Buck Controller with Integrated Gate Drivers and AVP |
| NCP5383_1 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2 Phase Buck Controller with Integrated Gate Drivers and AVP |
发布紧急采购，3分钟左右您将得到回复。