- 您现在的位置：买卖IC网 > Datasheet目录346 > NCP5680MUTXG (ON Semiconductor)IC LED DRIVER WHT HI EFF 24-UQFN Datasheet资料下载
参数资料
| 型号： | NCP5680MUTXG |
| 厂商： | ON Semiconductor |
| 文件页数： | 21/27页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER WHT HI EFF 24-UQFN |
| 产品变化通告： | Product Obsolescence 30/Jun/2011 |
| 标准包装： | 3,000 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 2 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 850kHz ~ 1.15MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 4.5 V ~ 5.3 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-UFQFN 裸露焊盘 |
| 供应商设备封装： | 24-UQFN（3.5x3.5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页
NCP5680
Photo Sense
When the photo sense is activated (bit PHEN = 1 in the
CONFIG0 register), the duration of the flash is automatically
reduced when enough light back from the photo target is
sensed through the external sensor. The analog signal present
at the PHSEN pin is amplified (depending upon the gain setup
by the MCU) and compared with the reference programmed
by the MCU: the photo flash pulse is switched OFF when the
input signal is higher than the content of the PHSEN register
(see Figure 19). The built ? in flip flop makes sure that a single
pulse is generated when the light feedback has been
acknowledged by the sensor. The flip flop is reset to the armed
position upon a new trigger flash command (coming from
either the I2C or from the TRGFL pin).
Figure 19. Typical Flash Pulses with Photo Sense Engaged
VSD
+VBat
VSB
D1
PHOTO
PHSEN
R
R/2
GND
GAIN
R1
22k
U1
GND
I2C
R/8
R/4
R/2
R
2R
4R
8R
R
I2C
+VREF
Comparator
Digital Setup
U1
STOP
Figure 20. Basic Photo Sense Structure
On the other hand, the VSD bias voltage is activated
when either the charge pump is active, or the ENPH bit in
the CONFIG0 register is High.
In order to minimize the influence of voltage offset,
operating the Photo Sense trigger level in the 360 mV to
1500 mV range is recommended.
Picture Light
The Picture Light current share the same internal current
mirror used to support the Torch/ Video function. The level
of current is controlled by the TILED register. In addition,
a 200 ms time out is automatically activated when the
TILED current is higher than 100 mA. On the other hand,
http://onsemi.com
21
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5890MUTXG | IC LED DRVR WHITE BCKLGT 16-UQFN |
| NCP5901BMNTBG | IC MOSFET DVR SYNC VR12 8-DFN |
| NCP5901MNTBG | IC MOSFET DVR SYNC VR12 8-DFN |
| NCP5911MNTBG | IC MOSFET DVR SYNC VR12 8-DFN |
| NCP692MN50T2GEVB | EVAL BOARD FOR NCP692MN50T2G |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP571 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:150 mA CMOS Low Iq Low Output Voltage Regulator |
| NCP57152 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.5 A, Very Low-Dropout (VLDO) Fast Transient Response Regulator |
| NCP57152DSADJR4G | 制造商:ON Semiconductor 功能描述:1.5A ADJ VLDO REGULATOR - Tape and Reel 制造商:ON Semiconductor 功能描述:1.5A ADJ VLDO REGULATOR - Cut TR (SOS) 制造商:ON Semiconductor 功能描述:REEL / 1.5A ADJ VLDO REGULATOR |
| NCP57152MNADJTYG | 制造商:ON Semiconductor 功能描述:1.5A ADJ VLDO REGULATOR - Tape and Reel 制造商:ON Semiconductor 功能描述:1.5A ADJ VLDO REGULATOR - Cut TR (SOS) 制造商:ON Semiconductor 功能描述:REEL / 1.5A ADJ VLDO REGULATOR |
| NCP571MN08TBG | 功能描述:直流/直流开关转换器 LDO RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。