- 您现在的位置：买卖IC网 > Datasheet目录482 > NCT65DMR2G (ON Semiconductor)IC TEMP MON TRIP POINT 8-MSOP Datasheet资料下载
参数资料
| 型号： | NCT65DMR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | IC TEMP MON TRIP POINT 8-MSOP |
| 标准包装： | 3,000 |
| 感应温度： | 70°C & 85°C 跳闸点 |
| 输出类型： | 开路漏极 |
| 电源电压： | 2.8 V ~ 3.6 V |
| 精确度： | ±1°C，±1.5°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
NCT65
Remote Sensing Diode
The NCT65 is designed to work with substrate transistors
built into processors or with discrete transistors. Substrate
transistors are generally PNP types with the collector
connected to the substrate. Discrete types are either PNP or
NPN transistors connected as diodes (base-shorted to
collector). If an NPN transistor is used, the collector and
capacitor across D+ and D ? close to the NCT65. This
capacitance can effect the temperature measurement, so
ensure that any capacitance seen at D+ and D ? is, at
maximum, 1,000 pF. This maximum value includes the
filter capacitance, plus any cable or stray capacitance
between the pins and the sensor diode.
base are connected to D+ and the emitter to D ? . If a PNP
transistor is used, the collector and base are connected to D ?
and the emitter to D+.
Layout Considerations
Digital boards can be electrically noisy environments, and
the NCT65 is measuring very small voltages from the
remote sensor, so care must be taken to minimize noise
induced at the sensor inputs. Take the following precautions:
GND
D+
D ?
GND
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
? Place the NCT65 as close as possible to the remote
sensing diode. Provided that the worst noise sources,
that is, clock generators, data/address busses etc., are
avoided, this distance can be 4 to 8 inches.
? Route the D+ and D ? tracks close together, in parallel,
with grounded guard tracks on each side. To minimize
inductance and reduce noise pickup, a 5 mil track width
and spacing is recommended. Provide a ground plane
under the tracks, if possible.
? Place a 0.1 m F bypass capacitor close to the V DD pin. In
extremely noisy environments, place an input filter
V DD
1
Figure 4. Typical Arrangement of Signal Tracks
Application Circuit
The figure below shows a typical application circuit for
the NCT65, using an embedded transistor on a GPU to
measure the temperature. The THERM1 p in can be used to
alert the system and throttle the GPU. The THERM2 pin can
be used to shutdown the system if necessary. Both pins
require pullup resistors to V DD or an alternative supply (up
to 3.6 V).
V+ (up to 3.6 V)
NCT65
T_TRIP = 85 ? C
10 k W
REFERENCE
+
COMPARATOR
4
THERM2
?
GPU
D+
D ?
2
3
LOW
PASS
FILTER
DIFFERENCE
AMPLIFIER
10 k W
REFERENCE
?
COMPARATOR
+
T_TRIP = 70 ? C
6
THERM1
5
7
8
GND
Figure 5. Typical Configuration Block Diagram
http://onsemi.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| NCV8440STT1G | MOSFET N CH 2.6A 59V SOT-223-4 |
| NDB5060L | MOSFET N-CH 60V 26A D2PAK |
| NDB6060 | MOSFET N-CH 60V 48A TO-263AB |
| NDB7060 | MOSFET N-CH 60V 75A D2PAK |
| NDC7001C | MOSFET N+P 60V 340MA SSOT6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCT6627UD | 制造商:Nuvoton Technology Corp 功能描述:IC LPC SUPER I/O 128LQFP |
| NCT675 | 制造商:New Concept Tools 功能描述:TOOLS, DRILL BITS; Kit Contents:31 Pieces of 5 Straight, 4 Phillips, 4 Pozidrive, 10 Hex, & 10 Torx Bits ;RoHS Compliant: NA |
| NCT6776D | 制造商:Nuvoton Technology Corp 功能描述:IC LPC SUPER I/O 128LQFP |
| NCT6776F | 制造商:Nuvoton Technology Corp 功能描述:LPC SUPER I/O, PECI 3.0, SST*, 制造商:Nuvoton Technology 功能描述:LPC SUPER I/O, PECI 3.0, SST*, |
| NCT6779D | 制造商:Nuvoton Technology Corp 功能描述:NEW 128-PIN SIO, BASICALLY PIN |
发布紧急采购，3分钟左右您将得到回复。