- 您现在的位置：买卖IC网 > Datasheet目录996 > OCB100-KIT (TT Electronics/Optek Technology)KIT CALIBRATION CIRC OPTO ASSY Datasheet资料下载
参数资料
| 型号： | OCB100-KIT |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | KIT CALIBRATION CIRC OPTO ASSY |
| 产品培训模块： | OCB100-KIT Auto-Calibration Design Kit |
| 标准包装： | 1 |
| 传感器类型： | 光学断续器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 嵌入式： | 否 |
| 已供物品： | 板，流体传感器，反射传感器，开槽型开关，线缆和样品 |
| 已用 IC / 零件： | OPB350C，OPB732CZ，OPB885CZ |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 相关产品： | 365-1534-ND - BOARD CALIBR WIRED OPTO ASSY 365-1533-ND - BOARD CALIBR CIRCUIT PCB MNT |
| 其它名称： | 365-1507 |
to a higher load resistor value in those cases. Place the shorting bar
between pins 2 & 3 and try calibrating again. In this case the OP-
B885CZ only needs to reach an Ic (ON) value of 2.5V / 10K = 0.25mA
to calibrate. We could have suggested the 10K load resistor to begin
with, but this exercise can show the importance of matching the
phototransistor load resistance to data sheet specifications of the par-
ticular sensor being interfaced to the OCB100CZ.
An example of an application where the OPB885Z could be used
in combination with the OCB100CZ would be where a semi-opaque
or semi-transmissive material needs to be sensed. Since the material
does not block all of the light, the sensor might see through the mate-
rial and not be able to detect its presence. The OCB100CZ solves this
problem by calibrating the sensor output at a level slightly higher than
the detection trip point. If the material to sense is 50% transmissive
or less, it will be sensed.
Another example would be when the difference in two semi-
transmissive materials needs to be detected, such as in a label
printer where a sensor is required to see through the liner of a roll of
labels, but detect the label. A sample label / liner is included in this
OCB100-KIT. Try the following experiment:
Insure that the shorting bar is placed between pins 2 & 3 to set
the load resistor at approximately 10K ohms. Place the gap between
the two labels in the center of the optical path. Calibrate the sensor.
Now move the labels back and forth in the gap to see that the green
LED lights when the labels are present, but does not light when the
label is present. Remove the label / liner from the gap completely.
The blue light of the OCB100CZ should now be lit.
OPTEK gives you the tools to help you take your ideas to market.
17
相关PDF资料 |
PDF描述 |
|---|---|
| OCB350L062Z | BOARD CALIBR CIRCUIT OPB350L062 |
| OJ-SS-112LM,000 | RELAY GEN PURPOSE SPST 3A 12V |
| OJ-SS-124DM,000 | RELAY GEN PURPOSE SPST 5A 24V |
| OJ-SS-124HM,000 | RELAY GEN PURPOSE SPST 10A 24V |
| OJE-SH-112HM,000 | RELAY GEN PURPOSE SPST 10A 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OCB100-KIT | 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit |
| OCB-1250 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1375 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1500 | 制造商:Heyco Products Inc 功能描述: |
| OCB350L062Z | 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L062 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装: |
发布紧急采购，3分钟左右您将得到回复。