- 您现在的位置：买卖IC网 > Datasheet目录996 > OCB100-KIT (TT Electronics/Optek Technology)KIT CALIBRATION CIRC OPTO ASSY Datasheet资料下载
参数资料
| 型号： | OCB100-KIT |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | KIT CALIBRATION CIRC OPTO ASSY |
| 产品培训模块： | OCB100-KIT Auto-Calibration Design Kit |
| 标准包装： | 1 |
| 传感器类型： | 光学断续器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 嵌入式： | 否 |
| 已供物品： | 板，流体传感器，反射传感器，开槽型开关，线缆和样品 |
| 已用 IC / 零件： | OPB350C，OPB732CZ，OPB885CZ |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 相关产品： | 365-1534-ND - BOARD CALIBR WIRED OPTO ASSY 365-1533-ND - BOARD CALIBR CIRCUIT PCB MNT |
| 其它名称： | 365-1507 |
preset phototransistor output level is reached.
At this time, the LED drive current is locked and maintained until
the calibration pin is grounded. If for some reason the LED drive cur-
rent reaches the maximum allowable value, a RED warning light will
turn on. During the calibration process, remote monitoring of J1-Pin
5 allows the designer to ensure the system is calibrated (this output
should be at the preset calibrated output level of 1/2 Vcc when the
calibration procedure is completed). Adjusting the phototransistor
load resistor may allow the system to calibrate properly.
After the calibration process is complete, the device is ready for
acknowledgement of a change in the signal. The design engineer
6
can monitor either the Analog Output (J1-Pin 5) or Logical Output
(J1-Pin 2 or J1-Pin 3).
Connection of the analog ouput to additional circuitry allows the
design engineer to set any reference point to recognize an optical
change for the device being monitored. The Analog Output can be
used with reflective devices to monitor small changes in the distance
from the device.
The Logical Output will change state once the preset optical light
condition is reached. Logic Out A” (mating connector orange wire)
switches when the optical output signal decreases below approxi-
mately 1/3 of Vcc while “Logic Out B” (mating connector blue wire)
switches when the optical output signal increases above approxi-
mately 2/3 of Vcc.
As with all optical devices with logic outputs, the switching condition
is consistent with the phototransistor receiving a preset light level.
OCB100-KIT
相关PDF资料 |
PDF描述 |
|---|---|
| OCB350L062Z | BOARD CALIBR CIRCUIT OPB350L062 |
| OJ-SS-112LM,000 | RELAY GEN PURPOSE SPST 3A 12V |
| OJ-SS-124DM,000 | RELAY GEN PURPOSE SPST 5A 24V |
| OJ-SS-124HM,000 | RELAY GEN PURPOSE SPST 10A 24V |
| OJE-SH-112HM,000 | RELAY GEN PURPOSE SPST 10A 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OCB100-KIT | 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit |
| OCB-1250 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1375 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1500 | 制造商:Heyco Products Inc 功能描述: |
| OCB350L062Z | 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L062 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装: |
发布紧急采购，3分钟左右您将得到回复。