- 您现在的位置：买卖IC网 > Datasheet目录996 > OCB100-KIT (TT Electronics/Optek Technology)KIT CALIBRATION CIRC OPTO ASSY Datasheet资料下载
参数资料
| 型号： | OCB100-KIT |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 21/24页 |
| 文件大小： | 0K |
| 描述： | KIT CALIBRATION CIRC OPTO ASSY |
| 产品培训模块： | OCB100-KIT Auto-Calibration Design Kit |
| 标准包装： | 1 |
| 传感器类型： | 光学断续器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 嵌入式： | 否 |
| 已供物品： | 板，流体传感器，反射传感器，开槽型开关，线缆和样品 |
| 已用 IC / 零件： | OPB350C，OPB732CZ，OPB885CZ |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 相关产品： | 365-1534-ND - BOARD CALIBR WIRED OPTO ASSY 365-1533-ND - BOARD CALIBR CIRCUIT PCB MNT |
| 其它名称： | 365-1507 |
USING THE OPB350C125Z WITH THE OCB100CZ
Note: The above discussion of the OCB350 series also applies to
using the wired OPB350W series and the OPB350C125Z with the
OCB100Z.
Connect the OCB100CZ to a power source as described on page 7
“Powering up the OCB100CZ”.
Plug the OPB350C125Z connector into the 4 pin Molex mating
connector on the OCB100CZ , and then apply power to the circuit.
Adjust the phototransistor emitter load resistor to equal approxi-
mately 2.5Kohm (RL @ 2.5 K) by placing the shorting bar on the board
betweens pins 1 & 2 (see table on pg. 9) of the header. Calibrate the
sensor by momentarily grounding pin 4 of connector J1 by touching
the green wire of the mating connector to the black wire (ground) of
the mating connector.
A short length of 1/8” clear tubing is included in the OCB100-KIT.
Try the following experiment. Snap the tubing into place in the
optical path of the OPB350C125Z. Calibrate the sensor. Insert water
into the tubing sample. The blue light on the OCB100CZ should
light when water is present in the optical path, and no LED should be
lit when water is not present.
OPTEK gives you the tools to help you take your ideas to market.
21
相关PDF资料 |
PDF描述 |
|---|---|
| OCB350L062Z | BOARD CALIBR CIRCUIT OPB350L062 |
| OJ-SS-112LM,000 | RELAY GEN PURPOSE SPST 3A 12V |
| OJ-SS-124DM,000 | RELAY GEN PURPOSE SPST 5A 24V |
| OJ-SS-124HM,000 | RELAY GEN PURPOSE SPST 10A 24V |
| OJE-SH-112HM,000 | RELAY GEN PURPOSE SPST 10A 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OCB100-KIT | 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit |
| OCB-1250 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1375 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1500 | 制造商:Heyco Products Inc 功能描述: |
| OCB350L062Z | 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L062 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装: |
发布紧急采购，3分钟左右您将得到回复。