- 您现在的位置：买卖IC网 > PDF目录367726 > P87C42 (INTEL CORP) UNIVERSAL PERIPHERAL INTERFACE CHMOS 8-BIT SLAVE MICROCONTROLLER PDF资料下载
参数资料
| 型号： | P87C42 |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | UNIVERSAL PERIPHERAL INTERFACE CHMOS 8-BIT SLAVE MICROCONTROLLER |
| 中文描述： | 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 11/25页 |
| 文件大小： | 345K |
| 代理商： | P87C42 |
UPI-C42/UPI-L42
b. Apply access code to appropriate inputs to put
the device into security mode.
c. Apply high voltage to EA and V
DD
pins.
d. Follow the programming procedure as per the
Quick-Pulse Programming Algorithm with known
data on the databus. Not only the security bit, but
also the security byte of the signature row is pro-
grammed.
e. Verify that the security byte of the signature
mode contains the same data as appeared on
the data bus. (If DB0–DB7
e
high, the security
byte will contain FFH.)
f. Read two consecutive known bytes from the
EPROM array and verify that the wrong data are
retrieved in at least one verification. If the
EPROM can still be read, the security bit may
have not been fully programmed though the se-
curity byte in the signature mode has.
Verification
Since the security bit address overlaps the address
of the security byte of the signature mode, it can be
used to check indirectly whether the security bit has
been programmed or not. Therefore, the security bit
verification is a mere read operation of the security
byte of the signature row (0FFH
e
security bit pro-
grammed; 00H
e
security bit unprogrammed). Note
that during the security bit programming, the reading
of the security byte does not necessarily indicate
that the security bit has been successfully pro-
grammed. Thus, it is recommended that two consec-
utive known bytes in the EPROM array be read and
the wrong data should be read at least once, be-
cause it is highly improbable that random data coin-
cides with the correct ones twice.
SIGNATURE MODE
The UPI-C42 has an additional 64 bytes of EPROM
available for Intel and user signatures and miscella-
neous purposes. The 64 bytes are partitioned as fol-
lows:
A.
Test code/checksumD
This can accommodate
up to 25 bytes of code for testing the internal
nodes that are not testable by executing from the
external memory. The test code/checksum is
present on ROMs, and OTPs.
B.
Intel signature
DThis allows the programmer to
read from the UPI-41AH/42AH/C42 the manu-
facturer of the device and the exact product
name. It facilitates automatic device identification
and will be present in the ROM and OTP ver-
sions. Location 10H contains the manufacturer
code. For Intel, it is 89H. Location 11H contains
the device code.
The code is 43H and 42H for the 8042AH/80C42
and OTP 8742AH/87C42, respectively. The
code is 44H for any device with the security bit
set by Intel.
C.
User signature
DThe user signature memory is
implemented in the EPROM and consists of 2
bytes for the customer to program his own signa-
ture code (for identification purposes and quick
sorting of previously programmed materials).
D.
Test signature
DThis memory is used to store
testing information such as: test data, bin num-
ber, etc. (for use in quality and manufacturing
control).
E.
Security byte
DThis byte is used to check
whether the security bit has been programmed
(see the security bit section).
F.
UPI-C42
CHMOS device. Location 20H contains the man-
ufacturer code and location 21H contains the de-
vice code. The Intel UPI-C42 manufacturer’s
code is 99H. The device ID’s are 82H for the
OTP version and 83H for the ROM version. The
device ID’s are the same for the UPI-L42.
Intel
Signature
DApplies
only
to
The signature mode can be accessed by setting
P10
e
0, P11–P17
e
1, and then following the pro-
gramming and/or verification procedures. The loca-
tion of the various address partitions are as shown in
Table 3.
SYNC MODE
The Sync Mode is provided to ease the design of
multiple controller circuits by allowing the designer
to force the device into known phase and state time.
The Sync Mode may also be utilized by automatic
test equipment (ATE) for quick, easy, and efficient
synchronizing between the tester and the DUT (de-
vice under test).
Sync Mode is enabled when SS pin is raised to high
voltage level of
a
12 volts. To begin synchroniza-
tion, T0 is raised to 5 volts at least four clock cycles
after SS. T0 must be high for at least four X2 clock
cycles to fully reset the prescaler and time state
generators. T0 may then be brought down during
low state of X2. Two clock cycles later, with the ris-
ing edge of X2, the device enters into Time State 1,
Phase 1. SS is then brought down to 5 volts 4 clocks
later after T0. RESET is allowed to go high 5 tCY (75
clocks) later for normal execution of code.
11
相关PDF资料 |
PDF描述 |
|---|---|
| P82C435 | ENHANCED GRAPHICS CONTROLLER / BUS INTERFACE |
| P82C436 | ENHANCED GRAPHICS CONTROLLER / BUS INTERFACE |
| P82C550A | STARLAN SERIAL INTERFACE |
| P82C551 | STARLAN HUB CONTROLLER |
| P83C053BBPNB | MICROCONTROLLER FOR TELEVISION AND VIDEO (MTV) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87C453EBAA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P87C453EBL | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| P87C453EBLKA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P87C453EFAA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P87C453EFL | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。