- 您现在的位置：买卖IC网 > PDF目录12056 > P89V51RD2FA,512 (NXP Semiconductors)IC 80C51 MCU FLASH 64K 44-PLCC PDF资料下载
参数资料
| 型号： | P89V51RD2FA,512 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 35/80页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 64K 44-PLCC |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 标准包装： | 26 |
| 系列： | 89V |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LCC（J 形引线） |
| 包装： | 管件 |
| 产品目录页面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1017-ND - BOARD 44-ZIF PLCC SOCKET 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP |
| 其它名称： | 568-1290-5 935276046512 P89V51RD2FA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
P89V51RB2_RC2_RD2_5
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 05 — 12 November 2009
40 of 80
NXP Semiconductors
P89V51RB2/RC2/RD2
8-bit microcontrollers with 80C51 core
The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the
following conditions are met at the time the nal shift pulse is generated: (a) RI = 0, and
(b) either SM2 = 0, or the received 9th data bit = 1.
If either of these conditions is not met, the received frame is irretrievably lost, and RI is not
set. If both conditions are met, the received 9th data bit goes into RB8, and the rst 8 data
bits go into SBUF.
6.6.8 Multiprocessor communications
UART modes 2 and 3 have a special provision for multiprocessor communications. In
these modes, 9 data bits are received or transmitted. When data is received, the 9th bit is
stored in RB8. The UART can be programmed so that when the stop bit is received, the
serial port interrupt will be activated only if RB8 = 1. This feature is enabled by setting bit
SM2 in SCON. One way to use this feature in multiprocessor systems is as follows:
When the master processor wants to transmit a block of data to one of several slaves, it
rst sends out an address byte which identies the target slave. An address byte differs
from a data byte in a way that the 9th bit is ‘1’ in an address byte and ‘0’ in the data byte.
With SM2 = 1, no slave will be interrupted by a data byte, i.e. the received 9th bit is ‘0’.
However, an address byte having the 9th bit set to ‘1’ will interrupt all slaves, so that each
slave can examine the received byte and see if it is being addressed or not. The
addressed slave will clear its SM2 bit and prepare to receive the data (still 9 bits long) that
follow. The slaves that weren’t being addressed leave their SM2 bits set and go on about
their business, ignoring the subsequent data bytes.
SM2 has no effect in mode 0, and in mode 1 can be used to check the validity of the stop
bit, although this is better done with the Framing Error ag. When UART receives data in
mode 1 and SM2 = 1, the receive interrupt will not be activated unless a valid stop bit is
received.
6.6.9 Automatic address recognition
Automatic Address Recognition is a feature which allows the UART to recognize certain
addresses in the serial bit stream by using hardware to make the comparisons. This
feature saves a great deal of software overhead by eliminating the need for the software to
examine every serial address which passes by the serial port. This feature is enabled for
the UART by setting the SM2 bit in SCON. In the 9 bit UART modes, mode 2 and mode 3,
the Receive Interrupt ag (RI) will be automatically set when the received byte contains
either the ‘Given’ address or the ‘Broadcast' address. The 9 bit mode requires that the 9th
information bit is a ‘1’ to indicate that the received information is an address and not data.
Using the Automatic Address Recognition feature allows a master to selectively
communicate with one or more slaves by invoking the Given slave address or addresses.
All of the slaves may be contacted by using the Broadcast address. Two Special Function
Registers are used to dene the slave’s address, SADDR, and the address mask,
SADEN. SADEN is used to dene which bits in the SADDR are to be used and which bits
are ‘don’t care’. The SADEN mask can be logically ANDed with the SADDR to create the
‘Given’ address which the master will use for addressing each of the slaves. Use of the
Given address allows multiple slaves to be recognized while excluding others.
This device uses the methods presented in Figure 16 to determine if a ‘Given’ or
‘Broadcast’ address has been received or not.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA16U2-AU | MCU AVR 16K FLASH USB 32TQFP |
| VI-J43-IX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VI-J42-IX-B1 | CONVERTER MOD DC/DC 15V 75W |
| VI-J41-IX-B1 | CONVERTER MOD DC/DC 12V 75W |
| VE-JTR-IX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89V51RD2FBC | 制造商:NXP Semiconductors 功能描述: |
| P89V51RD2FBC,557 | 功能描述:8位微控制器 -MCU 80C51 64K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89V51RD2FBC557 | 制造商:NXP 功能描述: |
| P89V51RD2FN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16/32/64 kB flash microcontroller with 1 kB RAM |
| P89V51RD2FN,112 | 功能描述:8位微控制器 -MCU 80C51 64K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。