- 您现在的位置：买卖IC网 > PDF目录12056 > P89V51RD2FA,512 (NXP Semiconductors)IC 80C51 MCU FLASH 64K 44-PLCC PDF资料下载
参数资料
| 型号： | P89V51RD2FA,512 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 54/80页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 64K 44-PLCC |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 标准包装： | 26 |
| 系列： | 89V |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LCC（J 形引线） |
| 包装： | 管件 |
| 产品目录页面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1017-ND - BOARD 44-ZIF PLCC SOCKET 622-1001-ND - USB IN-CIRCUIT PROG 80C51ISP |
| 其它名称： | 568-1290-5 935276046512 P89V51RD2FA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
PIC18F87K22 FAMILY
DS39960D-page 58
2009-2011 Microchip Technology Inc.
4.1.3
CLOCK TRANSITIONS AND STATUS
INDICATORS
The length of the transition between clock sources is
the sum of two cycles of the old clock source and
three to four cycles of the new clock source. This for-
mula assumes that the new clock source is stable.
The HF-INTOSC and MF-INTOSC are termed as
INTOSC in this chapter.
Three bits indicate the current clock source and its
status, as shown in Table 4-2. The three bits are:
OSTS (OSCCON<3>)
HFIOFS (OSCCON<2>)
SOSCRUN (OSCCON2<6>)
When the OSTS bit is set, the primary clock is providing
the device clock. When the HFIOFS or MFIOFS bit is
set, the INTOSC output is providing a stable 16 MHz
clock source to a divider that actually drives the device
clock. When the SOSCRUN bit is set, the SOSC oscil-
lator is providing the clock. If none of these bits are set,
either the LF-INTOSC clock source is clocking the
device or the INTOSC source is not yet stable.
If the internal oscillator block is configured as the
primary clock source by the FOSC<3:0> Configuration
bits (CONFIG1H<3:0>), then the OSTS and HFIOFS or
MFIOFS bits can be set when in PRI_RUN or
PRI_IDLE modes. This indicates that the primary clock
(INTOSC output) is generating a stable 16 MHz output.
Entering another INTOSC power-managed mode at
the same frequency would clear the OSTS bit.
4.1.4
MULTIPLE SLEEP COMMANDS
The power-managed mode that is invoked with the
SLEEP
instruction is determined by the setting of the
IDLEN bit at the time the instruction is executed. If
another SLEEP instruction is executed, the device will
enter the power-managed mode specified by IDLEN at
that time. If IDLEN has changed, the device will enter
the new power-managed mode specified by the new
setting.
4.2
Run Modes
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
4.2.1
PRI_RUN MODE
The PRI_RUN mode is the normal, Full-Power Execu-
tion mode of the microcontroller. This is also the default
mode upon a device Reset, unless Two-Speed Start-up
is enabled. (For details, see Section 28.4 “Two-Speed
.) In this mode, the OSTS bit is set. The
HFIOFS or MFIOFS bit may be set if the internal
oscillator block is the primary clock source. (See
.)
4.2.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock-switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the SOSC oscillator. This enables lower
power consumption while retaining a high-accuracy
clock source.
SEC_RUN mode is entered by setting the SCS<1:0>
bits to ‘01’. The device clock source is switched to the
SOSC oscillator (see Figure 4-1), the primary oscillator
is shut down, the SOSCRUN bit (OSCCON2<6>) is set
and the OSTS bit is cleared.
On transitions from SEC_RUN mode to PRI_RUN
mode, the peripherals and CPU continue to be clocked
from the SOSC oscillator while the primary clock is
started. When the primary clock becomes ready, a
clock switch back to the primary clock occurs (see
Figure 4-2). When the clock switch is complete, the
SOSCRUN bit is cleared, the OSTS bit is set and the
primary clock is providing the clock. The IDLEN and
SCS bits are not affected by the wake-up and the
SOSC oscillator continues to run.
TABLE 4-2:
SYSTEM CLOCK INDICATOR
Main Clock Source
OSTS
HFIOFSor
MFIOFS
SOSCRUN
Primary Oscillator
10
0
INTOSC (HF-INTOSC or
MF-INTOSC)
01
0
Secondary Oscillator
00
1
MF-INTOSC or
HF-INTOSC as Primary
Clock Source
11
0
LF-INTOSC is Running or
INTOSC is Not Yet Stable
00
0
Note 1:
Caution should be used when modifying
a single IRCF bit. At a lower VDD, it is
possible to select a higher clock speed
than is supportable by that VDD. Improper
device operation may result if the VDD/
FOSC specifications are violated.
2:
Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep mode or
one of the Idle modes, depending on the
setting of the IDLEN bit.
Note:
The SOSC oscillator can be enabled by
setting the SOSCGO bit (OSCCON2<3>).
If this bit is set, the clock switch to the
SEC_RUN mode can switch immediately
once SCS<1:0> are set to ‘01’.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA16U2-AU | MCU AVR 16K FLASH USB 32TQFP |
| VI-J43-IX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VI-J42-IX-B1 | CONVERTER MOD DC/DC 15V 75W |
| VI-J41-IX-B1 | CONVERTER MOD DC/DC 12V 75W |
| VE-JTR-IX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89V51RD2FBC | 制造商:NXP Semiconductors 功能描述: |
| P89V51RD2FBC,557 | 功能描述:8位微控制器 -MCU 80C51 64K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89V51RD2FBC557 | 制造商:NXP 功能描述: |
| P89V51RD2FN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16/32/64 kB flash microcontroller with 1 kB RAM |
| P89V51RD2FN,112 | 功能描述:8位微控制器 -MCU 80C51 64K FL / 1K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。