- 您现在的位置：买卖IC网 > PDF目录3777 > PCA9502BS,151 (NXP Semiconductors)IC I/O EXPANDER I2C/SPI 24HVQFN PDF资料下载
参数资料
| 型号： | PCA9502BS,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 24/25页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C/SPI 24HVQFN |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 490 |
| 接口： | I²C，SPI |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-HVQFN（4x4） |
| 包装： | 托盘 |
| 产品目录页面： | 824 (CN2011-ZH PDF) |
| 其它名称： | 568-3635 935281363151 PCA9502BS-S |
PCA9502_3
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 03 — 13 October 2006
8 of 25
NXP Semiconductors
PCA9502
8-bit I/O expander with I2C-bus/SPI interface
A slave receiver must generate an acknowledge after the reception of each byte, and a
master must generate one after the reception of each byte clocked out of the slave
transmitter.
There is an exception to the ‘acknowledge after every byte’ rule. It occurs when a master
is a receiver: it must signal an end of data to the transmitter by not signalling an
acknowledge on the last byte that has been clocked out of the slave. The acknowledge
related clock, generated by the master should still take place, but the SDA line will not be
pulled down. In order to indicate that this is an active and intentional lack of
acknowledgement, we shall term this special condition as a ‘negative acknowledge’.
9.2 Addressing and transfer formats
Each device on the bus has its own unique address. Before any data is transmitted on the
bus, the master transmits on the bus the address of the slave to be accessed for this
transaction. A well-behaved slave with a matching address, if it exists on the network,
should of course acknowledge the master's addressing. The addressing is done by the
rst byte transmitted by the master after the START condition.
An address on the network is seven bits long, appearing as the most signicant bits of the
address byte. The last bit is a direction (R/W) bit. A ‘0’ indicates that the master is
transmitting (write) and a ‘1’ indicates that the master requests data (read). A complete
data transfer, comprised of an address byte indicating a ‘write’ and two data bytes is
shown in Figure 8.
Fig 6.
Data transfer on the I2C-bus
S
P
SDA
SCL
MSB
0
1
6
7
8
0
1
2 to 7
8
ACK
002aab012
START
condition
STOP
condition
acknowledgement signal
from receiver
byte complete,
interrupt within receiver
clock line held LOW
while interrupt is serviced
Fig 7.
Acknowledge on the I2C-bus
S
01
6
7
8
002aab013
data output
by transmitter
data output
by receiver
SCL from master
START
condition
transmitter stays off of the bus
during the acknowledge clock
acknowledgement signal
from receiver
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9501D,118 | IC I/O EXPANDER I2C 8B 20SOIC |
| ATTINY44A-CCUR | MCU AVR 4KB FLASH 20MHZ 15UFBGA |
| 2-583717-7 | CONN CARD EDGE 14POS .100 PCB |
| ATTINY2313A-SUR | MCU AVR 2KB FLASH 20MHZ 20SOIC |
| ATTINY24A-MFR | MCU AVR 2KB FLASH 20MHZ 20QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9502BS-F | 功能描述:接口-I/O扩展器 8-BITI/O EXPDR W/I2C-SPI INTRF RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9503A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| PCA9504A | 功能描述:接口 - 专用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| PCA9504ADGG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Glue chip 4 |
| PCA9504ADGG,112 | 功能描述:接口 - 专用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。