- 您现在的位置：买卖IC网 > PDF目录3777 > PCA9502BS,151 (NXP Semiconductors)IC I/O EXPANDER I2C/SPI 24HVQFN PDF资料下载
参数资料
| 型号： | PCA9502BS,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 3/25页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C/SPI 24HVQFN |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 490 |
| 接口： | I²C，SPI |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-HVQFN（4x4） |
| 包装： | 托盘 |
| 产品目录页面： | 824 (CN2011-ZH PDF) |
| 其它名称： | 568-3635 935281363151 PCA9502BS-S |
PCA9502_3
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 03 — 13 October 2006
11 of 25
NXP Semiconductors
PCA9502
8-bit I/O expander with I2C-bus/SPI interface
9.3 Addressing
Before any data is transmitted or received, the master must send the address of the
receiver via the SDA line. The rst byte after the START condition carries the address of
the slave device and the read/write bit. Table 11 shows how the PCA9502’s address can
be selected by using A1 and A0 pins. For example, if these 2 pins are connected to VDD,
then the PCA9502’s address is set to 0x90, and the master communicates with it through
this address.
[1]
X = logic 0 for write cycle; X = logic 1 for read cycle.
9.4 Use of sub-addresses
When a master communicates with the PCA9502 it must send a sub-address in the byte
following the slave address byte. This sub-address is the internal address of the word the
master wants to access for a single byte transfer, or the beginning of a sequence of
locations for a multi-byte transfer. A sub-address is an 8-bit byte. Unlike the device
address, it does not contain a direction (R/W) bit, and like any byte transferred on the bus
it must be followed by an acknowledge.
A register write cycle is shown in Figure 10. The START is followed by a slave address
byte with the direction bit set to ‘write’, a sub-address byte, a number of data bytes, and a
STOP signal. The sub-address indicates which register the master wants to access. and
the data bytes which follow will be written one after the other to the sub-address location.
Table 11.
PCA9502 address map
A1
A0
VDD
0x90 (1001 000X)
VDD
VSS
0x92 (1001 001X)
VDD
SCL
0x94 (1001 010X)
VDD
SDA
0x96 (1001 011X)
VSS
VDD
0x98 (1001 100X)
VSS
0x9A (1001 101X)
VSS
SCL
0x9C (1001 110X)
VSS
SDA
0x9E (1001 111X)
SCL
VDD
0xA0 (1010 000X)
SCL
VSS
0xA2 (1010 001X)
SCL
0xA4 (1010 010X)
SCL
SDA
0xA6 (1010 011X)
SDA
VDD
0xA8 (1010 100X)
SDA
VSS
0xAA (1010 101X)
SDA
SCL
0xAC (1010 110X)
SDA
0xAE (1010 111X)
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9501D,118 | IC I/O EXPANDER I2C 8B 20SOIC |
| ATTINY44A-CCUR | MCU AVR 4KB FLASH 20MHZ 15UFBGA |
| 2-583717-7 | CONN CARD EDGE 14POS .100 PCB |
| ATTINY2313A-SUR | MCU AVR 2KB FLASH 20MHZ 20SOIC |
| ATTINY24A-MFR | MCU AVR 2KB FLASH 20MHZ 20QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9502BS-F | 功能描述:接口-I/O扩展器 8-BITI/O EXPDR W/I2C-SPI INTRF RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9503A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| PCA9504A | 功能描述:接口 - 专用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| PCA9504ADGG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Glue chip 4 |
| PCA9504ADGG,112 | 功能描述:接口 - 专用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。