- 您现在的位置：买卖IC网 > PDF目录299624 > PCA9534APWR (TEXAS INSTRUMENTS INC) 8 I/O, PIA-GENERAL PURPOSE, PDSO16 PDF资料下载
参数资料
| 型号： | PCA9534APWR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| 封装： | GREEN, PLASTIC, TSSOP-16 |
| 文件页数： | 37/41页 |
| 文件大小： | 985K |
| 代理商： | PCA9534APWR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页
Data From
Shift Register
Data From
Shift Register
Write Configuration
Pulse
Write Pulse
Read Pulse
Write Polarity
Pulse
Data From
Shift Register
Output Port
Register
Configuration
Register
Input Port
Register
Polarity
Inversion
Register
Polarity
Register Data
Input Port
Register Data
GND
ESD Protection
Diode
P0 to P7
VCC
Output Port
Register Data
Q1
Q2
D
CK
FF
Q
D
CK
FF
Q
D
CK
FF
Q
D
CK
FF
Q
To INT
www.ti.com
SCPS141F – SEPTEMBER 2006 – REVISED JUNE 2010
SIMPLIFIED SCHEMATIC OF P0 TO P7
A.
At power-on reset, all registers return to default values.
I/O Port
When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a high-impedance input. The input
voltage may be raised above VCC to a maximum of 5.5 V.
If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the output port register. In
this case, there are low-impedance paths between the I/O pin and either VCC or GND. The external voltage
applied to this I/O pin should not exceed the recommended levels for proper operation.
I
2C Interface
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply through a pull-up resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by a master sending a start condition, a high-to-low transition on
the SDA input/output while the SCL input is high (see Figure 1). After the start condition, the device address byte
is sent, MSB first, including the data direction bit (R/W).
After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA
input/output during the high of the ACK-related clock pulse. The address inputs (A0–A2) of the slave device must
not be changed between the start and the stop conditions.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (start or stop) (see Figure 2).
Copyright 2006–2010, Texas Instruments Incorporated
5
Product Folder Link(s): PCA9534A
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9554ADBRG4 | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| PCB1A24S | 24 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, SCREW |
| PCD25F98S0T20 | 25 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, PRESS FIT |
| PCFMB150E6 | 150 A, 600 V, N-CHANNEL IGBT |
| PCH-27-823 | 1 ELEMENT, 82 uH, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9534APWR | 制造商:Texas Instruments 功能描述:I2CLogicInterfaceDeviceICs |
| PCA9534APWRG4 | 功能描述:接口-I/O扩展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGTR | 功能描述:接口-I/O扩展器 Remote 8B I2C and Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGTRG4 | 功能描述:接口-I/O扩展器 Remote 8B I2C and Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGVR | 功能描述:接口-I/O扩展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。