- 您现在的位置：买卖IC网 > PDF目录299624 > PCA9534APWR (TEXAS INSTRUMENTS INC) 8 I/O, PIA-GENERAL PURPOSE, PDSO16 PDF资料下载
参数资料
| 型号： | PCA9534APWR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| 封装： | GREEN, PLASTIC, TSSOP-16 |
| 文件页数： | 41/41页 |
| 文件大小： | 985K |
| 代理商： | PCA9534APWR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页
SCL
Start Condition
Data 1 Valid
SDA
Write to Port
Data Out
From Port
R/W
ACK From Slave
1
9
8
7
6
5
4
3
2
Data 1
1
A2
0
1
S
1
A1 A0 0
A
0
A
P
tpv
Data to Port
Command Byte
Slave Address
Data
1/0
A2
0
1
S
1
A1 A0 0
A
1
0
A
P
SCL
SDA
Data to
Register
Start Condition
R/W
ACK From Slave
1
9
8
7
6
5
4
3
2
Data to Register
Command Byte
Slave Address
www.ti.com
SCPS141F – SEPTEMBER 2006 – REVISED JUNE 2010
Interrupt Output (INT)
An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time, tiv, the
signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original
setting, data is read from the port that generated the interrupt. Resetting occurs in the read mode at the
acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal.
Interrupts that occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of
the interrupt during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT.
Writing to another device does not affect the interrupt circuit, and a pin configured as an output cannot cause an
interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur, if the state of the pin
does not match the contents of the Input Port register. Because each 8-pin port is read independently, the
interrupt caused by port 0 is not cleared by a read of port 1 or vice versa.
The INT output has an open-drain structure and requires pullup resistor to VCC.
Bus Transactions
Data is exchanged between the master and PCA9534A through write and read commands.
Writes
Data is transmitted to the PCA9534A by sending the device address and setting the least-significant bit to a logic
0 (see Figure 4 for device address). The command byte is sent after the address and determines which register
receives the data that follows the command byte (see Figure 6 and Figure 7). There is no limitation on the
number of data bytes sent in one write transmission.
Figure 6. Write to Output Port Register
<br/>
Figure 7. Write to Configuration or Polarity Inversion Registers
Copyright 2006–2010, Texas Instruments Incorporated
9
Product Folder Link(s): PCA9534A
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9554ADBRG4 | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| PCB1A24S | 24 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, SCREW |
| PCD25F98S0T20 | 25 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, PRESS FIT |
| PCFMB150E6 | 150 A, 600 V, N-CHANNEL IGBT |
| PCH-27-823 | 1 ELEMENT, 82 uH, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9534APWR | 制造商:Texas Instruments 功能描述:I2CLogicInterfaceDeviceICs |
| PCA9534APWRG4 | 功能描述:接口-I/O扩展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGTR | 功能描述:接口-I/O扩展器 Remote 8B I2C and Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGTRG4 | 功能描述:接口-I/O扩展器 Remote 8B I2C and Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9534ARGVR | 功能描述:接口-I/O扩展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。