参数资料
| 型号： | PCA9535EMTTXG |
| 厂商： | ON Semiconductor |
| 文件页数： | 2/20页 |
| 文件大小： | 0K |
| 描述： | 16-BIT I/O EXPANDER |
| 标准包装： | 3,000 |
| 接口： | I²C 总线，SM 总线 |
| 输入/输出数： | 16 |
| 中断输出： | 是 |
| 频率 - 时钟： | 100kHz |
| 电源电压： | 1.65 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 带卷 (TR) |
| 包括： | * |
PCA9535E, PCA9535EC
http://onsemi.com
10
Registers 4 and 5: Polarity Inversion Registers
These registers allow the polarity of the data in the input
port registers to be inverted. The input port data polarity will
be inverted when its corresponding bit in these registers is
set (written with ‘1’), and retained when the bit is cleared
(written with a ‘0’).
Table 12. POLARITY INVERSION PORT 0 REGISTER
Bit
7
6
5
4
3
2
1
0
Symbol
N0.7
N0.6
N0.5
N0.4
N0.3
N0.2
N0.1
N0.0
Default
0
Table 13. POLARITY INVERSION PORT 1 REGISTER
Bit
7
6
5
4
3
2
1
0
Symbol
N1.7
N1.6
N1.5
N1.4
N1.3
N1.2
N1.1
N1.0
Default
0
Registers 6 and 7: Configuration Registers
The I/O pin directions are configured through the
configuration registers. When a bit in the configuration
registers is set (written with ‘1’), the bit’s corresponding port
pin is enabled as an input with the output driver in
highimpedance. When a bit is cleared (written with ‘0’),
the corresponding port pin is enabled as an output. At reset,
the device’s ports are inputs.
Table 14. CONFIGURATION PORT 0 REGISTER
Bit
7
6
5
4
3
2
1
0
Symbol
C0.7
C0.6
C0.5
C0.4
C0.3
C0.2
C0.1
C0.0
Default
1
Table 15. CONFIGURATION PORT 1 REGISTER
Bit
7
6
5
4
3
2
1
0
Symbol
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Default
1
Poweron Reset
Upon application of power, an internal PowerOn Reset
(POR) holds the PCA9535E/PCA9535EC in a reset
condition while VDD is ramping up. When VDD has reached
VPOR, the reset condition is released and the
PCA9535E/PCA9535EC registers and SMBus state
machine will initialize to their default states. The reset is
typically completed by the POR and the part enabled by the
time the power supply is above VPOR. However, when doing
a power reset cycle, it is necessary to lower the power supply
below 0.2 V, and then restored to the operating voltage.
I/O Port (See Figure 2)
When an I/O pin is configured as an input on the
PCA9535E, FETs Q1 and Q2 are off, creating a
highimpedance input. The input voltage may be raised
above VDD to a maximum of 5.5 V. In the case of
PCA9535EC, FET Q1 has been removed and the
opendrain FET Q2 will function the same as PCA9535E.
When the I/O pin is configured as an output on the
PCA9535E, then either Q1 or Q2 is enabled, depending on
the state of the output port register. With the PCA9535EC,
an external pullup is required to pull the I/O pin HIGH when
its corresponding output port register bit is a 1. Care should
be exercised if an external voltage is applied to an I/O
configured as an output because of the lowimpedance path
that exists between the pin and either VDD or VSS.
相关PDF资料 |
PDF描述 |
|---|---|
| JLC1562BFEL | IC BUS INTRFACE I2C I/O 16SOEIAJ |
| ATMEGA8515-16JUR | MCU AVR 8KB FLASH 16MHZ 44PLCC |
| PCA9555D/G-T | IC I/O EXPANDER I2C 16B 24SOIC |
| ATMEGA48-15AZV | MCU AVR 4K FLASH 15MHZ 32-TQFP |
| ATMEGA48-15AZ | MCU AVR 4K FLASH 15MHZ 32-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9535HF | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit I2C-bus and SMBus, low power I/O port with interrupt |
| PCA9535HF,118 | 功能描述:I2C 接口集成电路 16BIT I2C FM TP GPIO RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9535HF-T | 功能描述:I2C 接口集成电路 16BIT I2C FM TP GPIO INT RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9535PW | 功能描述:I2C 接口集成电路 I2C/SMBUS 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9535PW,112 | 功能描述:I2C 接口集成电路 I2C/SMBUS 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
发布紧急采购，3分钟左右您将得到回复。