- 您现在的位置：买卖IC网 > Datasheet目录349 > PCA9551BS,118 (NXP Semiconductors)IC LED DRIVER BLINKER 16-HVQFN Datasheet资料下载
参数资料
| 型号： | PCA9551BS,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 4/26页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER BLINKER 16-HVQFN |
| 产品培训模块： | LED Controllers I²C Bus Fundamentals |
| 标准包装： | 1 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | LED 闪烁器 |
| 频率： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 供应商设备封装： | 16-HVQFN |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 844 (CN2011-ZH PDF) |
| 配用： | 568-4002-ND - DEMO BOARD I2C 568-3615-ND - DEMO BOARD I2C |
| 其它名称： | 568-3388-6 |
NXP Semiconductors
Table 2.
PCA9551
8-bit I 2 C-bus LED driver with programmable blink rates
Pin description …continued
Symbol
Pin
SO16, TSSOP16
HVQFN16
Description
LED7
RESET
SCL
SDA
V DD
12
13
14
15
16
10
11
12
13
14
LED driver 7
reset input (active LOW)
serial clock line
serial data line
supply voltage
[1]
HVQFN16 package die supply ground is connected to both V SS pin and exposed center pad. V SS pin must
be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board
level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad
on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the
PCB in the thermal pad region.
6. Functional description
Refer to Figure 1 “Block diagram of PCA9551” .
6.1 Device address
Following a START condition, the bus master must output the address of the slave it is
accessing. The address of the PCA9551 is shown in Figure 5 . To conserve power, no
internal pull-up resistors are incorporated on the hardware selectable address pins and
they must be pulled HIGH or LOW.
slave address
1
1
0
0
A2
A1
A0 R/W
fixed
hardware
selectable
002aac505
Fig 5.
PCA9551 slave address
The last bit of the address byte de?nes the operation to be performed. When set to logic 1
a read is selected, while a logic 0 selects a write operation.
6.2 Control register
Following the successful acknowledgement of the slave address, the bus master will send
a byte to the PCA9551, which will be stored in the Control register.
0
0
0
AI
0
B2
B1
B0
Auto-Increment flag
register address
002aac506
Reset state: 00h
Fig 6.
Control register
The lowest 3 bits are used as a pointer to determine which register will be accessed.
PCA9551_8
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 08 — 31 July 2008
4 of 26
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9552D,118 | IC LED DRIVER BLINKER 24-SOIC |
| PCA9553DP/01,118 | IC LED DRIVER LINEAR 8-TSSOP |
| PCA9624PW,118 | IC LED DRIVER RGBA 24-TSSOP |
| PCA9625D/S911,518 | IC LED DRIVER RGBA 32-SOIC |
| PCA9626BS,518 | IC LED DRIVER RGBA 48HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9551BSHP | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9551BS-T | 功能描述:LED照明驱动器 8-BIT I2C FM OD LED BLK RST RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9551D | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit I2C LED driver with programmable blink rates |
| PCA9551D,112 | 功能描述:LED照明驱动器 I2C LED BLINKER 8BIT RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9551D,118 | 功能描述:LED照明驱动器 8-BIT I2C FM OD LED BLK RST RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。