- 您现在的位置：买卖IC网 > Datasheet目录349 > PCA9553DP/01,118 (NXP Semiconductors)IC LED DRIVER LINEAR 8-TSSOP Datasheet资料下载
参数资料
| 型号： | PCA9553DP/01,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 5/26页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 8-TSSOP |
| 产品培训模块： | LED Controllers I²C Bus Fundamentals |
| 标准包装： | 1 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | LED 闪烁器 |
| 频率： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 844 (CN2011-ZH PDF) |
| 其它名称： | 568-3392-6 |
NXP Semiconductors
PCA9553
4-bit I 2 C-bus LED driver with programmable blink rates
7. Functional description
Refer to Figure 1 “Block diagram” .
7.1 Device address
Following a START condition the bus master must output the address of the slave it is
accessing. The address of the PCA9553/01 is shown in Figure 5 and PCA9553/02 in
Figure 6 .
PCA9553TK uses the version /01 address.
slave address
slave address
1
1
0
0
0
1
0
R/W
1
1
0
0
0
1
1
R/W
002aad742
002aad743
Fig 5.
PCA9553/01 slave address
Fig 6.
PCA9553/02 slave address
The last bit of the address byte de?nes the operation to be performed. When set to logic 1
a read is selected, while a logic 0 selects a write operation.
7.2 Control register
Following the successful acknowledgement of the slave address, the bus master will send
a byte to the PCA9553 which will be stored in the Control register.
0
0
0
AI
0
B2
B1
B0
Reset state: 00h
Auto-Increment
flag
register address
002aad744
Fig 7.
Control register
The lowest 3 bits are used as a pointer to determine which register will be accessed.
If the Auto-Increment ?ag is set, the three low order bits of the Control register are
automatically incremented after a read or write. This allows the user to program the
registers sequentially. The contents of these bits will rollover to ‘000’ after the last register
is accessed.
When the Auto-Increment ?ag is set (AI = 1) and a read sequence is initiated, the
sequence must start by reading a register different from ‘0’ (B2 B1 B0 ≠ 0 0 0).
Only the 3 least signi?cant bits are affected by the AI ?ag.
Unused bits must be programmed with zeroes.
PCA9553_6
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 29 December 2008
5 of 26
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9624PW,118 | IC LED DRIVER RGBA 24-TSSOP |
| PCA9625D/S911,518 | IC LED DRIVER RGBA 32-SOIC |
| PCA9626BS,518 | IC LED DRIVER RGBA 48HVQFN |
| PCA9632DP2,118 | IC LED DRIVER RGBA 10-TSSOP |
| PCA9633BS,118 | IC LED DRIVER RGBA 16-HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9553DP02 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C LED driver with programmable blink rates |
| PCA9553TK | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C-bus LED driver with programmable blink rates |
| PCA9553TK,118 | 功能描述:LED照明驱动器 4BIT I2C FM OD LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9553TK/02 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C-bus LED driver with programmable blink rates |
| PCA9553TK/02,118 | 功能描述:LED照明驱动器 LED DRVR 4Segment 2.5V/3.3V/5V 8-Pin RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。