参数资料
| 型号： | PCA9574PW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 5/33页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 标准包装： | 96 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 1.1 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 包括： | POR |
| 其它名称： | 935285149112 PCA9574PW PCA9574PW-ND |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
PCA9574
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 4 — 25 April 2012
13 of 33
NXP Semiconductors
PCA9574
8-bit I2C-bus and SMBus, level translating, low volage GPIO
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9574 then resets to
the default value (power-up value) and is ready to be addressed again within the
specified bus free time. If the master sends a Repeated START instead, no reset is
performed. The I2C-bus master must interpret a non-acknowledge from the PCA9574
(at any time) as a ‘Software Reset Abort’. The PCA9574 does not initiate a software
reset.
7.9 Interrupt output (INT)
The open-drain active LOW interrupt is activated when one of the port pins changes state
and the port pin is configured as an input and the interrupt on it is not masked. The
interrupt is deactivated when the port pin input returns to its previous state or the Input
Port register is read. It is highly recommended to program the MSK register, and the CFG
registers during the initialization sequence after power-up, since any change to them
during Normal mode operation may cause undesirable interrupt events to happen.
Remark: Changing an I/O from an output to an input may cause a false interrupt to occur
if the state of the pin does not match the contents of the Input port register. Only a read of
the Input port register that contains the bit(s) image of the input(s) that generated the
interrupt clears the interrupt condition.
7.10 Standby
The PCA9574 goes into standby when the I2C-bus is idle. Standby supply current is lower
than 1.0
μA (typical).
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9574PW,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| 2-964577-2 | MULTIFIT RAHMEN 2P |
| 1-964577-5 | MULTIFIT RAHMEN 5P |
| 1-964576-3 | PCB RAHMEN 13P |
| PCA8574TS,118 | IC I/O EXPANDER I2C 8B 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9574PW-T | 功能描述:转换 - 电压电平 8-BIT I2C-BUS/SMBUS GPIO TRANS RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| PCA9575HF,118 | 功能描述:I2C 接口集成电路 16-BIT I2C-BUS SMBus LW Voltage GPIO RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9575HF118 | 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| PCA9575PW1,118 | 功能描述:I2C 接口集成电路 I2C Bus/ SMBus Level Translating 24-Pin RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9575PW2,118 | 功能描述:I2C 接口集成电路 I2C Bus/ SMBus Level Translating 28-Pin RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
发布紧急采购，3分钟左右您将得到回复。