- 您现在的位置：买卖IC网 > PDF目录268241 > PCF8563TD-T (NXP SEMICONDUCTORS) Real-time clock/calendar PDF资料下载
参数资料
| 型号： | PCF8563TD-T |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | XO, clock |
| 英文描述： | Real-time clock/calendar |
| 中文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封装： | 3.90 MM, PLASTIC, SO-8 |
| 文件页数： | 4/32页 |
| 文件大小： | 711K |
| 代理商： | PCF8563TD-T |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Philips Semiconductors
PCF8563
Real-time clock/calendar
Product specication
16 April 1999
12 of 30
9397 750 04855
Philips Electronics N.V. 1999. All rights reserved.
8.7 EXT_CLK test mode
A test mode is available which allows for on-board testing. In this mode it is possible
to set up test conditions and control the operation of the RTC.
The test mode is entered by setting bit TEST1 in the Control/Status1 register. The
CLKOUT pin then becomes an input. The test mode replaces the internal 64 Hz
signal with the signal that is applied to the CLKOUT pin. Every 64 positive edges
applied to CLKOUT will then generate an increment of one second.
The signal applied to the CLKOUT pin should have a minimum pulse width of 300 ns
and a minimum period of 1000 ns. The internal 64 Hz clock, now sourced from
CLKOUT, is divided down to 1 Hz by a 26 divide chain called a pre-scaler. The
pre-scaler can be set into a known state by using the STOP bit. When the STOP bit is
set, the pre-scaler is reset to 0. STOP must be cleared before the pre-scaler can
operate again. From a STOP condition, the rst 1 s increment will take place after
32 positive edges on CLKOUT. Thereafter, every 64 positive edges will cause a 1 s
increment.
Remark: Entry into EXT_CLK test mode is not synchronized to the internal 64 Hz
clock. When entering the test mode, no assumption as to the state of the pre-scaler
can be made.
8.7.1
Operation example
1. Enter the EXT_CLK test mode; set bit 7 of Control/Status 1 register (TEST = 1)
2. Set bit 5 of Control/Status 1 register (STOP = 1)
3. Clear bit 5 of Control/Status 1 register (STOP = 0)
4. Set time registers (Seconds, Minutes, Hours, Days, Weekdays, Months/Century
and Years) to desired value
5. Apply 32 clock pulses to CLKOUT
6. Read time registers to see the rst change
7. Apply 64 clock pulses to CLKOUT
8. Read time registers to see the second change.
Repeat steps 7 and 8 for additional increments.
8.8 Power-On Reset (POR) override mode
The POR duration is directly related to the crystal oscillator start-up time. Due to the
long start-up times experienced by these types of circuits, a mechanism has been
built in to disable the POR and hence speed up on-board test of the device. The
setting of this mode requires that the I2C-bus pins, SDA and SCL, be toggled in a
specic order as shown in Figure 5. All timing values are required minimum.
Once the override mode has been entered, the chip immediately stops being reset
and normal operation starts i.e. entry into the EXT_CLK test mode via I2C-bus
access. The override mode is cleared by writing a logic 0 to bit TESTC. Re-entry into
the override mode is only possible after TESTC is set to logic 1. Setting TESTC to
logic 0 during normal operation has no effect except to prevent entry into the POR
override mode.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12C671T-10E | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C671T-10I | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C672 | EPROM Memory Programming Specification |
| PIC12C672-10 | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C672-10E | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCF8563T-F4 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Real-time clock/calendar |
| PCF8563TF4.118 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Real-time clock/calendar |
| PCF8563TS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Real-time clock/calendar |
| PCF8563TS/4 | 制造商:NXP Semiconductors 功能描述:RTC/Calender,1.8-5.5V,PCF8563TS/4 |
| PCF8563TS/4,118 | 功能描述:实时时钟 ULTRA LOW PWR CLOCK CALENDAR RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。