- 您现在的位置：买卖IC网 > PDF目录21898 > PE43404MLI-Z (Peregrine Semiconductor)IC RF DSA 4-BIT 75 OHM 20-QFN PDF资料下载
参数资料
| 型号： | PE43404MLI-Z |
| 厂商： | Peregrine Semiconductor |
| 文件页数： | 3/11页 |
| 文件大小： | 0K |
| 描述： | IC RF DSA 4-BIT 75 OHM 20-QFN |
| 标准包装： | 1 |
| 系列： | UltraCMOS™ |
| 衰减值： | 15dB |
| 容差： | ±0.25dB |
| 频率范围： | 0 ~ 2GHz |
| 阻抗： | 75 欧姆 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 其它名称： | 1046-1044-6 |
PE43404
Product Specification
Evaluation Kit
The Digital Attenuator Evaluation Kit was designed to
ease customer evaluation of the PE43404 DSA.
J9 is used in conjunction with the supplied DC cable to
supply V DD , GND, and –V DD . If use of the internal
negative voltage generator is desired, then connect –
V DD (black banana plug) to ground. If an external –V DD
is desired, then apply -3V.
J1 should be connected to the LPT1 port of a PC with
the supplied control cable. The evaluation software is
written to operate the DSA in serial mode, so switch 7
(P/S) on the DIP switch SW1 should be ON with all
other switches off. Using the software, enable or
disable each attenuation setting to the desired
combined attenuation. The software automatically
programs the DSA each time an attenuation state is
enabled or disabled.
Note: Jumper J6 supplies power to the evaluation
board support circuits.
To evaluate the Power Up options, first disconnect the
control cable from the evaluation board. The control
cable must be removed to prevent the PC port from
biasing the control pins.
During power up with P/S=1 high and LE=1, the default
power-up signal attenuation is set to the value present
on the four control bits on the four parallel data inputs
(C1 to C8). This allows any one of the 32 attenuation
settings to be specified as the power-up state.
During power up with P/S=0 high and LE=0, the control
bits are automatically set to one of two possible values
presented through the PUP interface. These two
values are selected by the power-up control bit, PUP2,
as shown in Table 6.
Pins 1 and 7 are open and may be connected to any
Figure 4. Evaluation Board Layout
Peregrine Specification 101-0112
Figure 5. Evaluation Board Schematic
Peregrine Specification 102-0142
bias.
J18
SMA
1
Z=75 Ohm
R25
N/C
0 OHM
1
2
N/C
RFIN
C8
RFOUT
15
14
C8
R24 0 OHM
Z=75 Ohm
1
J19
SMA
DATA
R23
10K
CLK
LE
3
4
5
DATA
CLK
LE
U4
MLPQ4X4
PS
VNEG
GND
13
12
11
PS
-VDD
or GND
VDD
4
3
2
J20
SUPPLY
1
Note: Resistor on pin 3 is required and
should be placed as close to the part
C14
100pF
C12
0.1 μ F
VDD
as possible to avoid package
resonance and meet error
specifications over frequency.
C10
100pF
C9
0.1 μ F
Document No. 70-0258-02 │ www.psemi.com
?2008 Peregrine Semiconductor Corp. All rights reserved.
Page 3 of 11
Logo updated under non-rev change. Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| DK703 | LCD DPM +5V 2V 4.5 DIGIT |
| DK704 | LCD DPM +9V 200MV 4.5 DIGIT |
| 4309-52 | IC DSA 6BIT 50 OHM 24-QFN |
| DK702 | LCD DPM +5V 200MV 4.5 DIGIT |
| ELSH-F91R3-0LPNM-BR4R6 | LED SHUEN 3W HI PWR RED SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PE4341 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:SSMB Jack Right Angle Connector Solder Attachment Thru Hole PCB, .100 inch x .031 inch Hole Spacing |
| PE4342 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:Mini UHF Male Connector Crimp/Solder Attachment For RG58 |
| PE4344 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:N Male Connector Crimp/Solder Attachment For RG8X, PE-C240 |
| PE4346 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:3/4 inch-20 Twinax Female Connector Clamp/Solder Attachment For PE-S330 |
| PE4347 | 制造商:PASTERNACK 制造商全称:Pasternack Enterprises, Inc. 功能描述:3/4 inch-20 Twinax Female Connector Solder Attachment 4 Hole Flange Solder Cup Terminal, .718 inch Hole Spacing |
发布紧急采购，3分钟左右您将得到回复。