参数资料
| 型号： | PI2007-EVAL2 |
| 厂商： | Vicor Corporation |
| 文件页数： | 17/19页 |
| 文件大小： | 0K |
| 描述： | EVAL BRD FOR PI2007 12V/15A |
| 产品培训模块： | Cool-ORing? Series |
| 标准包装： | 1 |
| 系列： | Picor®, Cool-ORing® |
| 主要目的： | 电源管理，O 环控制器/负荷分载 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | PI2007 |
| 已供物品： | 板 |
| 其它名称： | 1102-1058 |
?
Layout Recommendation:
Use the following general guidelines when designing
printed circuit boards. An example of the typical land
pattern for a DFN PI2007 and SO-8/PowerPak
?
?
?
It is best to connect the gate of the MOSFET to
the GATE pin of the controller with a short trace. A
gate resistor (R G ) is added to slow down the gate
turn off if needed.
The VC bypass capacitor should be located as
close as possible to the VC and SGND pins.
Place the PI2007 and VC bypass capacitor on the
same layer of the board. The VC pin and C VC
PCB trace should not contain any vias.
In an application where SGND is floating, a low
forward voltage drop Schottky diode has to be
added in parallel with C VC to protect the controller
during an input voltage short fault.
?
?
?
PGND pin of the controller carries high peak
current during gate pull down, Connect PGND pin
with a wide trace to the C VC terminal at SGND.
Make sure that SGND trace and PGND trace
connect only at C VC terminal.
Connections from the SP and SN pins to the
MOSFET source and drain pins respectively
should be as short as possible
Connect all MOSFET source pins together with a
Figure 21: PI2007 controller and MOSFET layout
recommendation in a floating application.
wide trace to reduce trace parasitics and to
accommodate the high current input. Similarly,
connect all MOSFET Drain pins together with a
wide trace to accommodate the high current
output.
Figure 22: PI2007 controller and MOSFET layout
recommendation in a non-floating application
Picor Corporation ? picorpower.com
PI2007
Rev 1.3
Page 17 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| PI2126-EVAL1 | EVALUATION BOARD FOR PI2126 |
| PI2127-EVAL1 | EVAL BRD FOR PI2127 60V/12A |
| PI2161-EVAL1 | EVALUATION BOARD FOR PI2161 |
| PI2211-EVAL1 | BOARD EVAL FOR PI2211 |
| PI5101-EVAL1 | EVALUATION BOARD FOR PI5101 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI200MC-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Module |
| PI201M-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Sensor |
| PI20-5,08 | 功能描述:可插拔接线端子 PCB Hdr, 45 Deg, 5,08 PitchOpen End, 20pole, 12A,300V,Grn RoHS:否 制造商:Phoenix Contact 产品:Plugs 系列:PTS 端接类型:Spring Cage 位置/触点数量:5 线规量程:26-14 节距:5 mm 电流额定值:10 A 电压额定值:250 V 安装风格: 安装角: 触点电镀: |
| PI-205M | 制造商:Polycase 功能描述:Enclosure, Computer, Desktop, ABS,UL94-5VA, Blue, 4x3x1.375 In, For Raspberry Pi |
| PI2061-00-QEIG | 制造商:Vicor Corporation 功能描述:PI2061 Series 8.5 - 10.5 V 4 A Load Disconnect Switch Controller IC - TDFN-10 |
发布紧急采购，3分钟左右您将得到回复。