参数资料
| 型号： | PI2007-EVAL2 |
| 厂商： | Vicor Corporation |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | EVAL BRD FOR PI2007 12V/15A |
| 产品培训模块： | Cool-ORing? Series |
| 标准包装： | 1 |
| 系列： | Picor®, Cool-ORing® |
| 主要目的： | 电源管理，O 环控制器/负荷分载 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | PI2007 |
| 已供物品： | 板 |
| 其它名称： | 1102-1058 |
?
Figure 13: PI2007 performance in response to a fault (input short), configured for a +48V application as shown in
Application Information:
The PI2007 is designed to replace ORing diodes in
high current redundant power architectures.
Replacing a traditional diode with a PI2007 controller
IC and a low on-state resistance N-channel MOSFET
will result in significant power dissipation reduction as
well as board space reduction, efficiency improvement
and additional protection features. This section
describes in detail the procedure to follow when
designing with the PI2007 Active ORing controller and
N-Channel MOSFETs. Two different Active ORing
design examples are presented.
VC Bias:
The PI2007 has a separate input (VC) that provides
power to the control circuitry, the charge pump and
the gate driver. An internal regulator clamps the VC
voltage (V VC-SGND ) to 11.7V. A bypass ceramic
capacitor (C VC = 1μF) has to be connected between
VC and SGND to hold V VC-SGND steady. Also, the Gate
turn off return (PGND) should be connected to SGND
at the C VC termination to keep SGND noise free when
the Gate is turned off in response to a fault.
In 12V system applications, where the input voltage
(Vin) is between 10V and 14V, connect the VR pin to
Vin and connect SGND and PGND to the Vin return.
A 420Ω internal resistor is connected between the VR
pin and the VC pin.
In high voltage applications, above 14V, a bias
resistor (R PG ) and low current low forward voltage
drop Schottky diode are required. Connect one
terminal of R PG to the SGND and PGND and the other
terminal to ground (Vin return). The Schottky diode
anode will be connected to the SGND pin and its
cathode connected at the VC pin. See typical
application drawings on page 1.
Recommended Schottky:
PMEG3005AEA : from NXP or equivalent
R PG selection for input voltage greater than 14V:
Picor Corporation ? picorpower.com
PI2007
Rev 1.3
Page 9 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| PI2126-EVAL1 | EVALUATION BOARD FOR PI2126 |
| PI2127-EVAL1 | EVAL BRD FOR PI2127 60V/12A |
| PI2161-EVAL1 | EVALUATION BOARD FOR PI2161 |
| PI2211-EVAL1 | BOARD EVAL FOR PI2211 |
| PI5101-EVAL1 | EVALUATION BOARD FOR PI5101 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI200MC-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Module |
| PI201M-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Sensor |
| PI20-5,08 | 功能描述:可插拔接线端子 PCB Hdr, 45 Deg, 5,08 PitchOpen End, 20pole, 12A,300V,Grn RoHS:否 制造商:Phoenix Contact 产品:Plugs 系列:PTS 端接类型:Spring Cage 位置/触点数量:5 线规量程:26-14 节距:5 mm 电流额定值:10 A 电压额定值:250 V 安装风格: 安装角: 触点电镀: |
| PI-205M | 制造商:Polycase 功能描述:Enclosure, Computer, Desktop, ABS,UL94-5VA, Blue, 4x3x1.375 In, For Raspberry Pi |
| PI2061-00-QEIG | 制造商:Vicor Corporation 功能描述:PI2061 Series 8.5 - 10.5 V 4 A Load Disconnect Switch Controller IC - TDFN-10 |
发布紧急采购，3分钟左右您将得到回复。