参数资料
| 型号： | PI2EQX5804CNJE |
| 厂商： | Pericom |
| 文件页数： | 21/23页 |
| 文件大小： | 0K |
| 描述： | IC PCI-E REDRIVER 100LBGA |
| 标准包装： | 176 |
| 系列： | ReDriver™ |
| 类型： | 转接驱动器 |
| Tx/Rx类型： | CML |
| 电容 - 输入： | 50pF |
| 电源电压： | 1.15 V ~ 1.25 V |
| 电流 - 电源： | 800mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-BGA |
| 供应商设备封装： | 100-LBGA（11x11） |
| 包装： | 托盘 |
7
PS8926B
06/08/09
PI2EQX5804C
5.0Gbps 4-Lane PCIe 2.0 ReDriver with
Equalization & Emphasis
The RESET# input is used to reset the receiver detect state machine to its initial state. The start of the receiver detect
cycle starts when RESET# transitions from low to high.
When a Receiver Detect cycle is begins the differential channel pins are enabled with a 2K-Ohm pullup to VDD. A 50-
Ohm Receiver termination will change the pin level. This pin level is evaluated after a xed time-out, and the channel
is then set into the proper operating state. The output signals RX50_A and RX50_B represent the receiver detect result
for their specic channels.
The I/O Operation table summaries the relationships and operation of receiver detect and other signals involved with
I/O control.
Table 4 - I/O Operation Control
Control Inputs
Detection
States
Data Channel I/O
PD# RXD_x RESET#
RX50
SIG_x Input Termination Output Termination Mode
0
X
Hi-Z
Full IC power down, all channels dis-
abled
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled, output pulls to VDD.
Receiver detect reset
10
1
X
0
50-Ohm pull-
down
2K-Ohm pull-up
Channel enabled, no input signal, output
pulls to VDD. Receiver detect disabled
10
1
X
1
50-Ohm pull-
down
50-Ohm pull-up
Channel enabled, valid input signal
detected, output driving. Receiver detect
disabled.
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled. Receiver detect reset.
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled, output pulls to VDD.
Receiver detect enabled, no receiver
detected.
11
1
0
50-Ohm pull-
down
2K-Ohm pull-up
Channel inactive, output pulls to VDD.
Receiver detect enabled, receiver de-
tected. No input signal
11
1
50-Ohm pull-
down
50-Ohm pull-up
Channel active, valid input signal de-
tected, output driving. Receiver detect
enabled, load detected.
09-0001
相关PDF资料 |
PDF描述 |
|---|---|
| PI2EQX5864CZFE | IC PCI-E REDRIVER 56TQFN |
| PI2EQX5904NJE | IC PCIE 2.0 REDRIVER 100LBGA |
| PI2EQX5964ZFE | IC PCIE 2.0 REDRIVER 56TQFN |
| PI2EQX6804-ANJE | IC REDRIVER 100LBGA |
| PI2EQX6864-AZFE | IC REDRIVER 56TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI2EQX5804CNJEX | 功能描述:缓冲器和线路驱动器 PCI-Express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| Pi2EQX5804DNJE | 功能描述:缓冲器和线路驱动器 RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| PI2EQX5804DNJEX | 功能描述:缓冲器和线路驱动器 5.0Gbps 4 lane PCIe 2.0 Redriver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| PI2EQX5864 | 制造商:PERICOM 制造商全称:Pericom Semiconductor Corporation 功能描述:5.0Gbps 4-Lane PCI Express GenII Re-Driver with Equalization, Emphasis, &I2C Control |
| PI2EQX5864CZFE | 功能描述:缓冲器和线路驱动器 PCI express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。