- 您现在的位置：买卖IC网 > PDF目录11639 > PIC10F206-E/MC (Microchip Technology)IC PIC MCU FLASH 512X12 8DFN PDF资料下载
参数资料
| 型号： | PIC10F206-E/MC |
| 厂商： | Microchip Technology |
| 文件页数： | 20/94页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 512X12 8DFN |
| 标准包装： | 150 |
| 系列： | PIC® 10F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 4MHz |
| 外围设备： | POR，WDT |
| 输入/输出数： | 3 |
| 程序存储器容量： | 768B（512 x 12） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 24 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 配用： | AC164334-ND - MODULE SOCKET FOR 8L 2X3MM DFN AC163020-2-ND - ADAPTER PROGRAM PIC10F 2X3 DFN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
2007 Microchip Technology Inc.
DS41239D-page 25
PIC10F200/202/204/206
5.0
I/O PORT
As with any other register, the I/O register(s) can be
written and read under program control. However, read
instructions (e.g., MOVF GPIO, W) always read the I/O
pins independent of the pin’s Input/Output modes. On
Reset, all I/O ports are defined as input (inputs are at
high-impedance) since the I/O control registers are all
set.
5.1
GPIO
GPIO is an 8-bit I/O register. Only the low-order 4 bits
are used (GP<3:0>). Bits 7 through 4 are unimple-
mented and read as ‘0’s. Please note that GP3 is an
input-only pin. Pins GP0, GP1 and GP3 can be config-
ured with weak pull-ups and also for wake-up on
change. The wake-up on change and weak pull-up
functions are not pin selectable. If GP3/MCLR is config-
ured as MCLR, weak pull-up is always on and wake-up
on change for this pin is not enabled.
5.2
TRIS Registers
The Output Driver Control register is loaded with the
contents of the W register by executing the TRIS f
instruction. A ‘1’ from a TRIS register bit puts the corre-
sponding output driver in a High-Impedance mode. A
‘0’ puts the contents of the output data latch on the
selected pins, enabling the output buffer. The excep-
tions are GP3, which is input-only and the GP2/T0CKI/
COUT/FOSC4 pin, which may be controlled by various
registers. See Table 5-1.
The TRIS registers are “write-only” and are set (output
drivers disabled) upon Reset.
TABLE 5-1:
ORDER OF PRECEDENCE
FOR PIN FUNCTIONS
5.3
I/O Interfacing
The equivalent circuit for an I/O port pin is shown in
Figure 5-1. All port pins, except GP3 which is input-
only, may be used for both input and output operations.
For input operations, these ports are non-latching. Any
input must be present until read by an input instruction
(e.g., MOVF GPIO, W). The outputs are latched and
remain unchanged until the output latch is rewritten. To
use a port pin as output, the corresponding direction
control bit in TRIS must be cleared (= 0). For use as an
input, the corresponding TRIS bit must be set. Any I/O
pin (except GP3) can be programmed individually as
input or output.
FIGURE 5-1:
PIC10F200/202/204/206
EQUIVALENT CIRCUIT
FOR A SINGLE I/O PIN
Note:
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
Priority
GP0
GP1
GP2
GP3
1
CIN+
CIN-
FOSC4
I/MCLR
2
TRIS GPIO
COUT
—
3
—
—T0CKI
—
4
—
—TRIS GPIO
—
Data
Bus
Q
D
Q
CK
Q
D
Q
CK
P
N
WR
Port
TRIS
‘f’
Data
TRIS
RD Port
VSS
VDD
I/O
pin
W
Reg
Latch
Reset
Note 1: See Table 3-2 for buffer type.
VSS
VDD
(1)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B6L-CU-S | CONVERTER MOD DC/DC 28V 200W |
| PIC10F206T-I/MC | IC PIC MCU FLASH 512X12 8DFN |
| VI-B6J-CU-S | CONVERTER MOD DC/DC 36V 200W |
| VI-B63-CU-S | CONVERTER MOD DC/DC 24V 200W |
| PIC10LF320-E/OT | IC MCU 8BIT 256B FLASH SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC10F206-I/MC | 功能描述:8位微控制器 -MCU 0.75KB 24B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC10F206-I/OT | 制造商:Microchip Technology Inc 功能描述:8BIT PIC10 RISC 0.75KB FLASH 4 - Bulk |
| PIC10F206-I/P | 功能描述:8位微控制器 -MCU .75kBF 24RM 4I/O Ind Temp PDIP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC10F206T | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers |
| PIC10F206T-E/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。