- 您现在的位置：买卖IC网 > PDF目录3883 > PIC12C672T-10I/MF (Microchip Technology)IC MCU OTP 2KX14 W/AD 8-DFN PDF资料下载
参数资料
| 型号： | PIC12C672T-10I/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 48/129页 |
| 文件大小： | 0K |
| 描述： | IC MCU OTP 2KX14 W/AD 8-DFN |
| 标准包装： | 3,300 |
| 系列： | PIC® 12C |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 10MHz |
| 外围设备： | POR，WDT |
| 输入/输出数： | 5 |
| 程序存储器容量： | 3.5KB（2K x 14） |
| 程序存储器类型： | OTP |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 数据转换器： | A/D 4x8b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 配用： | AC164324-ND - MODULE SKT FOR MPLAB 8DFN/16QFN XLT08DFN2-ND - SOCKET TRANSITION ICE 14DIP/8DFN XLT08DFN-ND - SOCKET TRANSITION ICE 8DFN AC164032-ND - ADAPTER PICSTART PLUS 8DFN/DIP AC124001-ND - MODULE SKT PROMATEII 8DIP/SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页
1999 Microchip Technology Inc.
DS30561B-page 25
PIC12C67X
5.0
I/O PORT
As with any other register, the I/O register can be
written and read under program control. However, read
instructions (i.e., MOVF GPIO,W) always read the I/O
pins independent of the pin’s input/output modes. On
RESET, all I/O ports are defined as input (inputs are at
hi-impedance), since the I/O control registers are all
set.
5.1
GPIO
GPIO is an 8-bit I/O register. Only the low order 6 bits
are used (GP<5:0>). Bits 6 and 7 (SDA and SCL,
respectively) are used by the EEPROM peripheral on
the PIC12CE673/674.
Refer to Section 6.0 and
Appendix B for use of SDA and SCL. Please note that
GP3 is an input only pin. The configuration word can
set several I/O’s to alternate functions. When acting as
alternate functions, the pins will read as ‘0’ during port
read. Pins GP0, GP1 and GP3 can be configured with
weak pull-ups and also with interrupt-on-change. The
interrupt on change and weak pull-up functions are not
pin selectable. If pin 4, (GP3), is configured as MCLR,
a weak pull-up is always on. Interrupt-on-change for
this pin is not set and GP3 will read as '0'. Interrupt-on-
change is enabled by setting bit GPIE, INTCON<3>.
Note that external oscillator use overrides the GPIO
functions on GP4 and GP5.
5.2
TRIS Register
This register controls the data direction for GPIO. A '1'
from a TRIS Register bit puts the corresponding output
driver in a hi-impedance mode. A '0' puts the contents
of the output data latch on the selected pins, enabling
the output buffer. The exceptions are GP3, which is
input only and its TRIS bit will always read as '1', while
GP6 and GP7 TRIS bits will read as ’0’.
Upon reset, the TRIS Register is all '1's, making all
pins inputs.
TRIS for pins GP4 and GP5 is forced to a ’1’ where
appropriate. Writes to TRIS <5:4> will have an effect
in EXTRC and INTRC oscillator modes only. When
GP4 is configured as CLKOUT, changes to TRIS<4>
will have no effect.
Note:
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
5.3
I/O Interfacing
The equivalent circuit for an I/O port pin is shown in
Figure 5-1 through Figure 5-5. All port pins, except
GP3, which is input only, may be used for both input
and output operations. For input operations, these
ports are non-latching. Any input must be present until
read by an input instruction (i.e., MOVF GPIO,W). The
outputs are latched and remain unchanged until the
output latch is rewritten. To use a port pin as output,
the corresponding direction control bit in TRIS must be
cleared (= 0). For use as an input, the corresponding
TRIS bit must be set. Any I/O pin (except GP3) can be
programmed individually as input or output.
Port pins GP6 (SDA) and GP7 (SCL) are used for the
serial EEPROM interface on the PIC12CE673/674.
These port pins are not available externally on the
package.
Users should avoid writing to pins GP6
(SDA) and GP7 (SCL) when not communicating with
the serial EEPROM memory. Please see Section 6.0,
EEPROM Peripheral Operation, for information on
serial EEPROM communication.
Note:
On a Power-on Reset, GP0, GP1, GP2
and GP4 are configured as analog inputs
and read as '0'.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12C672T-04I/MF | IC MCU OTP 2KX14 W/AD 8-DFN |
| PIC12C671T-10I/MF | IC MCU OTP 1KX14 W/AD 8-DFN |
| PIC12LC671T-04I/MF | IC MCU OTP 1KX14 LV W/AD 8-DFN |
| PIC12C671T-04I/MF | IC MCU OTP 1KX14 W/AD 8-DFN |
| PIC12C508AT-04I/MF | IC MCU OTP 512X12 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC12C67X | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory |
| PIC12C67X_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory |
| PIC12CE-04/EJW | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12CE-04/EP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12CE-04/ESM | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。