- 您现在的位置：买卖IC网 > PDF目录11539 > PIC16F1527-E/MR (Microchip Technology)MCU 28KB FLASH 1536B RAM 64-QFN PDF资料下载
参数资料
| 型号： | PIC16F1527-E/MR |
| 厂商： | Microchip Technology |
| 文件页数： | 87/94页 |
| 文件大小： | 0K |
| 描述： | MCU 28KB FLASH 1536B RAM 64-QFN |
| 标准包装： | 40 |
| 系列： | PIC® XLP™ 16F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | I²C，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 54 |
| 程序存储器容量： | 28KB（16K x 14） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 数据转换器： | A/D 30x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页第93页第94页
2011 Microchip Technology Inc.
Preliminary
DS41458B-page 53
PIC16(L)F1526/27
5.2
Clock Source Types
Clock sources can be classified as external or internal.
External clock sources rely on external circuitry for the
clock source to function. Examples are: oscillator mod-
ules (EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resis-
tor-Capacitor (RC) mode circuits.
Internal clock sources are contained internally within the
oscillator module. The internal oscillator block has two
internal oscillators that are used to generate the internal
system clock sources: the 16 MHz High-Frequency
Internal Oscillator and the 31 kHz Low-Frequency
Internal Oscillator (LFINTOSC).
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS) bits in the OSCCON register. See Section 5.3
for additional information.
5.2.1
EXTERNAL CLOCK SOURCES
An external clock source can be used as the device
system clock by performing one of the following
actions:
Program the FOSC<2:0> bits in the Configuration
Word 1 to select an external clock source that will
be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to:
- Secondary oscillator during run-time, or
- An external clock source determined by the
value of the FOSC bits.
See Section 5.3 “Clock Switching”for more informa-
tion.
5.2.1.1
EC Mode
The External Clock (EC) mode allows an externally
generated logic level signal to be the system clock
source. When operating in this mode, an external clock
source
is
connected
to
the
OSC1
input.
OSC2/CLKOUT is available for general purpose I/O or
CLKOUT. Figure 5-2 shows the pin connections for EC
mode.
EC mode has three power modes to select from through
Configuration Word 1:
High power, 4-20 MHz (FOSC = 111)
Medium power, 0.5-4 MHz (FOSC = 110)
Low power, 0-0.5 MHz (FOSC = 101)
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 5-2:
EXTERNAL CLOCK (EC)
MODE OPERATION
5.2.1.2
LP, XT, HS Modes
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2 (Figure 5-3). The three modes select
a low, medium or high gain setting of the internal
inverter-amplifier to support various resonator types
and speed.
LP
Oscillator mode selects the lowest gain setting of the
internal inverter-amplifier. LP mode current consumption
is the least of the three modes. This mode is designed to
drive only 32.768 kHz tuning-fork type crystals (watch
crystals).
XT
Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS
Oscillator mode selects the highest gain setting of the
internal inverter-amplifier. HS mode current consumption
is the highest of the three modes. This mode is best
suited for resonators that require a high drive setting.
Figure 5-3 and Figure 5-4 show typical circuits for
quartz crystal and ceramic resonators, respectively.
OSC1/CLKIN
OSC2/CLKOUT
Clock from
Ext. System
PIC MCU
FOSC/4 or I/O(1)
Note
1:
Output depends upon CLKOUTEN bit of the
Configuration Word 1.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-21H-IY-B1 | CONVERTER MOD DC/DC 52V 50W |
| VE-21F-IY-B1 | CONVERTER MOD DC/DC 72V 50W |
| PIC16LF1527-E/MR | MCU PIC 28KB FLASH 64QFN |
| VE-21B-IY-B1 | CONVERTER MOD DC/DC 95V 50W |
| 31-220N-RFX | BNC ADAPTER BULKHEAD, 50 OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC16F1527-I/MR | 功能描述:8位微控制器 -MCU 28KB FL 1536B RAM 10bit ADC 1.8-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16F1527-I/MR | 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC16F 20 MHz 64-QFN 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC16F, 20 MHz, 64-QFN; Controller Family/Series:PIC16F; Core Size:8bit; No. of I/O's:54; Program Memory Size:28KB; RAM Memory Size:1536Byte; CPU Speed:20MHz; Oscillator Type:External, Internal; No. of Timers:9 ;RoHS Compliant: No |
| PIC16F1527-I/PT | 功能描述:8位微控制器 -MCU 14KB Flash RAM 768b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16F1527-I/PT | 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC16F 20 MHz 64-TQFP 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC16F, 20MHz, TQFP-64 |
| PIC16F1527T-I/MR | 功能描述:8位微控制器 -MCU 28KB FL 1536B RAM 10bit ADC 1.8-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。