参数资料
型号: PIC16LC62B-04/SP
厂商: Microchip Technology
文件页数: 80/120页
文件大小: 0K
描述: IC MCU OTP 2KX14 PWM 28DIP
产品培训模块: Asynchronous Stimulus
标准包装: 15
系列: PIC® 16C
核心处理器: PIC
芯体尺寸: 8-位
速度: 4MHz
连通性: I²C,SPI
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 22
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: OTP
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 2.5 V ~ 5.5 V
振荡器型: 外部
工作温度: 0°C ~ 70°C
封装/外壳: 28-DIP(0.300",7.62mm)
包装: 管件
PIC16C62B/72A
DS35008B-page 62
Preliminary
1999 Microchip Technology Inc.
10.10
Interrupts
The interrupt control register (INTCON) records individ-
ual interrupt requests in flag bits. It also has individual
and global interrupt enable bits.
A global interrupt enable bit, GIE (INTCON<7>)
enables or disables all interrupts. When bit GIE is
enabled, and an interrupt’s flag bit and mask bit are set,
the interrupt will vector immediately. Individual inter-
rupts can be disabled through their corresponding
enable bits in various registers. Individual interrupt flag
bits are set regardless of the status of the GIE bit. The
GIE bit is cleared on reset.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine and sets the GIE bit, which re-
enables interrupts.
The RB0/INT pin interrupt, the RB port change interrupt
and the TMR0 overflow interrupt flags are contained in
the INTCON register.
The peripheral interrupt flags are contained in the spe-
cial function registers PIR1 and PIR2. The correspond-
ing interrupt enable bits are contained in special
function registers PIE1 and PIE2, and the peripheral
interrupt enable bit is contained in special function reg-
ister INTCON.
When an interrupt is responded to, the GIE bit is
cleared to disable any further interrupts, the return
address is pushed onto the stack and the PC is loaded
with 0004h. Once in the interrupt service routine, the
source of the interrupt can be determined by polling the
interrupt flag bits. The interrupt flag bit must be cleared
in software before re-enabling interrupts to avoid recur-
sive interrupts.
For external interrupt events, such as the INT pin or
PORTB change interrupt, the interrupt latency will be
three or four instruction cycles, depending on when the
interrupt event occurs. The latency is the same for one
or two cycle instructions. Individual interrupt flag bits
are set regardless of the status of their corresponding
mask bit or the GIE bit
FIGURE 10-7: INTERRUPT LOGIC
Note:
Individual interrupt flag bits are set regard-
less of the status of their corresponding
mask bit or the GIE bit.
ADIF(1)
ADIE(1)
SSPIF
SSPIE
CCP1IF
CCP1IE
TMR2IF
TMR2IE
TMR1IF
TMR1IE
T0IF
T0IE
INTF
INTE
RBIF
RBIE
GIE
PEIE
Wake-up (If in SLEEP mode)
Interrupt to CPU
Note 1: The A/D module is not implemented on the PIC16C62B.
相关PDF资料
PDF描述
VI-B21-IW-S CONVERTER MOD DC/DC 12V 100W
VI-B6V-CU-F3 CONVERTER MOD DC/DC 5.8V 200W
VI-23Z-IV CONVERTER MOD DC/DC 2V 60W
VI-B6V-CU-F2 CONVERTER MOD DC/DC 5.8V 200W
VI-B6M-CU-F4 CONVERTER MOD DC/DC 10V 200W
相关代理商/技术参数
参数描述
PIC16LC62BT-04/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LC62BT-04/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LC62BT-04I/ML 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LC62BT-04I/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LC62BT-04I/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT