收藏本站
参数资料
型号： PIC18F46J50-I/PT
厂商： Microchip Technology
文件页数： 12/164页
文件大小： 0K
描述： IC PIC MCU FLASH 64KB 44-TQFP
产品培训模块： XLP Deep Sleep Mode
PIC18 J Series MCU Overview
PIC18F MPLAB® Starter Kit
8-bit PIC® Microcontroller Portfolio
标准包装： 160
系列： PIC® XLP™ 18F
核心处理器： PIC
芯体尺寸： 8-位
速度： 48MHz
连通性： I²C，SPI，UART/USART，USB
外围设备： 欠压检测/复位，DMA，POR，PWM，WDT
输入/输出数： 34
程序存储器容量： 64KB（32K x 16）
程序存储器类型： 闪存
RAM 容量： 3.8K x 8
电压 - 电源 (Vcc/Vdd)： 2.15 V ~ 3.6 V
数据转换器： A/D 13x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 44-TQFP
包装： 托盘
产品目录页面： 657 (CN2011-ZH PDF)
配用： AC164330-ND - MODULE SKT FOR 44TQFP 18F45J10
2011 Microchip Technology Inc.
DS39931D-page 109
PIC18F46J50 FAMILY
7.5
Writing to Flash Program Memory
The programming block is 32 words or 64 bytes.
Programming one word or 2 bytes at a time is also
supported.
Table writes are used internally to load the holding reg-
isters needed to program the Flash memory. There are
64 holding registers used by the table writes for
programming.
Since the Table Latch (TABLAT) is only a single byte, the
TBLWT
instruction may need to be executed 64 times for
each programming operation (if WPROG = 0). All of the
table write operations will essentially be short writes
because only the holding registers are written. At the
end of updating the 64 holding registers, the EECON1
register must be written to in order to start the
programming operation with a long write.
The long write is necessary for programming the
internal Flash. Instruction execution is halted while in a
long write cycle. The long write will be terminated by
the internal programming timer.
The on-chip timer controls the write time. The
write/erase voltages are generated by an on-chip
charge pump, rated to operate over the voltage range
of the device.
FIGURE 7-5:
TABLE WRITES TO FLASH PROGRAM MEMORY
7.5.1
FLASH PROGRAM MEMORY WRITE
SEQUENCE
The sequence of events for programming an internal
program memory location should be:
1.
Read 1024 bytes into RAM.
2.
Update data values in RAM as necessary.
3.
Load the Table Pointer register with the address
being erased.
4.
Execute the erase procedure.
5.
Load the Table Pointer register with the address
of the first byte being written, minus 1.
6.
Write the 64 bytes into the holding registers with
auto-increment.
7.
Set the WREN bit (EECON1<2>) to enable byte
writes.
8.
Disable interrupts.
9.
Write 0x55 to EECON2.
10. Write 0xAA to EECON2.
11. Set the WR bit. This will begin the write cycle.
12. The CPU will stall for the duration of the write for
TIW (see Parameter D133A).
13. Re-enable interrupts.
14. Repeat Steps 6 through 13 until all 1024 bytes
are written to program memory.
15. Verify the memory (table read).
An example of the required code is provided in
Example 7-3 on the following page.
Note 1:
Unlike previous PIC devices, devices of
the PIC18F46J50 family do not reset the
holding registers after a write occurs. The
holding registers must be cleared or
overwritten before a
programming
sequence.
2:
To maintain the endurance of the pro-
gram memory cells, each Flash byte
should not be programmed more than
once between erase operations. Before
attempting to modify the contents of the
target cell a second time, an erase of the
target page, or a bulk erase of the entire
memory, must be performed.
TABLAT
TBLPTR = xxxx3F
TBLPTR = xxxxx1
TBLPTR = xxxxx0
Write Register
TBLPTR = xxxxx2
Program Memory
Holding Register
8
Note:
Before setting the WR bit, the Table
Pointer address needs to be within the
intended address range of the 64 bytes in
the holding register.
相关PDF资料
PDF描述
PIC18F46K20-E/P IC PIC MCU FLASH 32KX16 40-DIP
PIC18F46K20-I/MV MCU PIC 64KB FLASH 40QFN
PIC18F47J53-I/ML IC PIC MCU 128KB FLASH 44QFN
PIC18F65K90-I/MR IC MCU 8BIT 32KB FLASH 64QFN
PIC18F66K80-I/MR MCU PIC 64KB FLASH 64QFN
相关代理商/技术参数
参数描述
PIC18F46J50T-I/ML 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F46J50T-I/PT 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F46J53-I/ML 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F46J53-I/PT 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F46J53T-I/ML 功能描述:8位微控制器 -MCU USB 64KB Flash 4KB RAM 12 MIPS 12b ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*