- 您现在的位置：买卖IC网 > PDF目录11447 > PIC18F86J16T-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 80TQFP PDF资料下载
参数资料
| 型号： | PIC18F86J16T-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 47/107页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 80TQFP |
| 产品培训模块： | Asynchronous Stimulus PIC18 J Series MCU Overview |
| 标准包装： | 1,200 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 48MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，LVD，POR，PWM，WDT |
| 输入/输出数： | 68 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 3930 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 数据转换器： | A/D 15x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 80-TQFP |
| 包装： | 带卷 (TR) |
| 配用： | AC162091-ND - HEADER MPLAB ICD2 18F87J11 64/80 MA180020-ND - MODULE PLUG-IN HPC EXPL 18F87J11 AC164328-ND - MODULE SKT FOR 80TQFP |
| 其它名称： | PIC18F86J16T-I/PTTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页
PIC18F87J11 FAMILY
DS39778E-page 44
2007-2012 Microchip Technology Inc.
3.5.3
INTERNAL OSCILLATOR OUTPUT
FREQUENCY AND TUNING
The internal oscillator block is calibrated at the factory
to produce an INTOSC output frequency of 8 MHz. It
can be adjusted in the user’s application by writing to
TUN<5:0> (OSCTUNE<5:0>) in the OSCTUNE
register (Register 3-2).
When the OSCTUNE register is modified, the INTOSC
frequency will begin shifting to the new frequency. The
oscillator will stabilize within 1 ms. Code execution
continues during this shift and there is no indication that
the shift has occurred.
The INTRC oscillator operates independently of the
INTOSC source. Any changes in INTOSC across
voltage and temperature are not necessarily reflected
by changes in INTRC or vice versa. The frequency of
INTRC is not affected by OSCTUNE.
3.5.4
INTOSC FREQUENCY DRIFT
The INTOSC frequency may drift as VDD or tempera-
ture changes, and can affect the controller operation in
a variety of ways. It is possible to adjust the INTOSC
frequency by modifying the value in the OSCTUNE reg-
ister. Depending on the device, this may have no effect
on the INTRC clock source frequency.
Tuning INTOSC requires knowing when to make the
adjustment, in which direction it should be made, and in
some cases, how large a change is needed. Three
compensation techniques are shown here.
3.5.4.1
Compensating with the EUSARTx
An adjustment may be required when the EUSARTx
begins to generate Framing Errors or receives data
with errors while in Asynchronous mode. Framing
Errors indicate that the device clock frequency is too
high. To adjust for this, decrement the value in
OSCTUNE to reduce the clock frequency. On the other
hand, errors in data may suggest that the clock speed
is too low. To compensate, increment OSCTUNE to
increase the clock frequency.
3.5.4.2
Compensating with the Timers
This technique compares device clock speed to some
reference clock. Two timers may be used; one timer is
clocked by the peripheral clock, while the other is
clocked by a fixed reference source, such as the
Timer1 oscillator.
Both timers are cleared, but the timer clocked by the
reference generates interrupts. When an interrupt
occurs, the internally clocked timer is read and both
timers are cleared. If the internally clocked timer value
is much greater than expected, then the internal
oscillator block is running too fast. To adjust for this,
decrement the OSCTUNE register.
3.5.4.3
Compensating with the CCP Module
in Capture Mode
A CCP module can use free-running Timer1 (or
Timer3), clocked by the internal oscillator block and an
external event with a known period (i.e., AC power
frequency). The time of the first event is captured in the
CCPRxH:CCPRxL registers and is recorded for use
later. When the second event causes a capture, the
time of the first event is subtracted from the time of the
second event. Since the period of the external event is
known, the time difference between events can be
calculated.
If the measured time is much greater than the
calculated time, the internal oscillator block is running
too fast. To compensate, decrement the OSCTUNE
register. If the measured time is much less than the
calculated time, the internal oscillator block is running
too slow. To compensate, increment the OSCTUNE
register.
3.6
Reference Clock Output
In addition to the FOSC/4 clock output in certain oscilla-
tor modes, the device clock in the PIC18F87J11 family
can also be configured to provide a reference clock out-
put signal to a port pin. This feature is available in all
oscillator configurations and allows the user to select a
greater range of clock sub-multiples to drive external
devices in the application.
This reference clock output is controlled by the
REFOCON register (Register 3-3). Setting the ROON
bit (REFOCON<7>) makes the clock signal available
on the REFO (RE3) pin. The RODIV<3:0> bits enable
the selection of 16 different clock divider options.
The ROSSLP and ROSEL bits (REFOCON<5:4>) con-
trol the availability of the reference output during Sleep
mode. The ROSEL bit determines if the oscillator on
OSC1 and OSC2, or the current system clock source,
is used for the reference clock output. The ROSSLP bit
determines if the reference source is available on RE3
when the device is in Sleep mode.
To use the reference clock output in Sleep mode, both
the ROSSLP and ROSEL bits must be set. The device
clock must also be configured for an EC or HS mode;
otherwise, the oscillator on OSC1 and OSC2 will be
powered down when the device enters Sleep mode.
Clearing the ROSEL bit allows the reference output
frequency to change as the system clock changes
during any clock switches.
The REFOCON register is an alternate SFR and
shares the same memory address as the OSCCON
register. It is accessed by setting the ADSHR bit in the
WDTCON register (WDTCON<4>).
相关PDF资料 |
PDF描述 |
|---|---|
| PIC24FJ128GA006T-I/PT | IC PIC MCU FLASH 128K 64TQFP |
| PIC16LF872T-I/SS | IC MCU FLASH 2KX14 EE A/D 28SSOP |
| PIC16LF870T-I/SS | IC MCU FLASH 2KX14 EE A/D 28SSOP |
| VI-J4L-IY-B1 | CONVERTER MOD DC/DC 28V 50W |
| VI-J4K-IY-B1 | CONVERTER MOD DC/DC 40V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18F86J50-I/PT | 功能描述:8位微控制器 -MCU 64KB Flash 3936byte RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J50T-I/PT | 功能描述:8位微控制器 -MCU 64KB FLSH 3936Bs RAM USB 2.0 nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J55-I/PT | 功能描述:8位微控制器 -MCU 96KB FLSH 3936Bs RAM USB 2.0 nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J55T-I/PT | 功能描述:8位微控制器 -MCU 96KB FLSH 3936Bs RAM USB 2.0 nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J60-I/PT | 功能描述:8位微控制器 -MCU 64KB FL 12KB RAM 10BASE-T RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。