- 您现在的位置：买卖IC网 > PDF目录11268 > PIC18LF8722T-I/PT (Microchip Technology)IC PIC MCU FLASH 64KX16 80TQFP PDF资料下载
参数资料
| 型号： | PIC18LF8722T-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 64KX16 80TQFP |
| 产品培训模块： | Asynchronous Stimulus |
| 标准包装： | 1,200 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，HLVD，POR，PWM，WDT |
| 输入/输出数： | 70 |
| 程序存储器容量： | 128KB（64K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 1K x 8 |
| RAM 容量： | 3.8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 80-TQFP |
| 包装： | 带卷 (TR) |
2006 Microchip Technology Inc.
DS80221C-page 9
PIC18F6627/6722/8627/8722
25. Module: EUSART
In rare situations, one or more extra zero bytes
have been observed in a packet transmitted by the
module operating in Asynchronous mode. The
actual data is not lost or corrupted; only unwanted
(extra) zero bytes are observed in the packet.
This situation has only been observed when the
contents of the transmit buffer, TXREGx, are trans-
ferred to the TSRx during the transmission of a
Stop bit. For this to occur, three things must
happen in the same instruction cycle:
TXREGx is written to;
the baud rate counter overflows (at the end of
the bit period); and
a Stop bit is being transmitted (shifted out of
TSRx).
Work around
If possible, do not use the module’s double buffer
capability. Instead, load the TXREGx register
when the TRMT bit (TXSTAx<1>) is set, indicating
the TSRx is empty.
If double-buffering is used and back-to-back
transmission is performed, then load TXREGx
immediately after TXxIF is set or wait 1-bit time after
TXxIF is set. Both solutions prevent writing TXREGx
while a Stop bit is transmitted. Note that TXxIF is set
at the beginning of the Stop bit transmission.
26. Module: EUSART
When performing back-to-back transmission in 9-bit
mode (TX9D bit in the TXSTAx register is set), the
second byte may be corrupted if it is written into
TXREGx immediately after the TMRT bit is set.
Work around
Execute a software delay, at least one-half the
transmission’s bit time, after TMRT is set and prior
to writing subsequent bytes into TXREGx.
Date Codes that pertain to this issue:
All engineering and production devices.
If transmission is intermittent, then do the following:
Wait for the TRMT bit to be set before
loading TXREGx
Alternatively, use a free timer resource to time
the baud period. Set up the timer to overflow
at the end of the Stop bit, then start the timer
when you load the TXREGx. Do not load the
TXREGx when timer is about to overflow.
Date Codes that pertain to this issue:
All engineering and production devices.
27. Module: EUSART
With the auto-wake-up option enabled by setting
the WUE (BAUDCONx<1>) bit, the RCxIF bit will
become set on a high-to-low transition on the RXx
pin. However, the WUE bit may not clear within
1TCY of a low-to-high transition on RXx. While the
WUE bit is set, reading the receive buffer,
RCREGx, will not clear the RCxIF interrupt flag.
Therefore, the first opportunity to automatically
clear RCxIF by reading RCREGx may take longer
than expected.
Work around
There are two work arounds available:
1. Clear the WUE bit in software, after the wake-
up event has occurred, prior to reading the
receive buffer, RCREGx.
2. Poll the WUE bit and read RCREGx after the
WUE bit is automatically cleared.
Date Codes that pertain to this issue:
All engineering and production devices.
28. Module: MSSP (SPI Mode)
In SPI mode, the SDOx output may change after
the inactive clock edge of the bit ‘0’ output. This
may affect some SPI components that read data
over 300 ns after the inactive edge of SCKx.
Work around
None
Date Codes that pertain to this issue:
All engineering and production devices.
Note:
RCxIF can only be cleared by reading
RCREGx.
相关PDF资料 |
PDF描述 |
|---|---|
| DG613DY-E3 | IC SWITCH QUAD NO/NC 16-SOIC |
| PIC24EP256GU814-E/PH | IC MCU 16BIT 256KB FLASH 144TQFP |
| DSPIC33EP256MU814-E/PH | IC DSC 16BIT 256KB FLASH 144TQFP |
| DG612DY-E3 | IC SWITCH QUAD SPST 16-SOIC |
| PIC16C76-10I/SO | IC MCU OTP 8KX14 A/D PWM 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18LF8723-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF8723T-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF96J65-I/PT | 功能描述:IC PIC MCU FLASH 48KX16 100TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 18F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP |
| PIC1-R68-JT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
发布紧急采购，3分钟左右您将得到回复。