- 您现在的位置：买卖IC网 > PDF目录11268 > PIC18LF8722T-I/PT (Microchip Technology)IC PIC MCU FLASH 64KX16 80TQFP PDF资料下载
参数资料
| 型号： | PIC18LF8722T-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 64KX16 80TQFP |
| 产品培训模块： | Asynchronous Stimulus |
| 标准包装： | 1,200 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，HLVD，POR，PWM，WDT |
| 输入/输出数： | 70 |
| 程序存储器容量： | 128KB（64K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 1K x 8 |
| RAM 容量： | 3.8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 80-TQFP |
| 包装： | 带卷 (TR) |
2006 Microchip Technology Inc.
DS80221C-page 11
PIC18F6627/6722/8627/8722
32. Module: MSSP (I2C Mode)
It has been observed that, following a Power-on
Reset, I2C mode may not initialize properly by just
configuring the SCLx and SDAx pins as either
inputs or outputs. This has only been seen in a few
unique system environments.
A test of a statistically significant sample of pre-
production systems, across the voltage and
current range of the application's power supply,
should indicate if a system is susceptible to this
issue.
Work around
Before configuring the module for I2C operation:
1. Configure the SCLx and SDAx pins as outputs
by clearing their corresponding TRIS bits.
2. Force SCLx and SDAx low by clearing the
corresponding LAT bits.
3. While keeping the LAT bits clear, configure
SCLx and SDAx as inputs by setting their TRIS
bits.
Once this is done, use the SSPxCON1 and
SSPxCON2 registers to configure the proper I2C
mode as before.
Date Codes that pertain to this issue:
All engineering and production devices.
33. Module: MSSP (I2C Mode)
In I2C Master mode, the RCEN bit is set by soft-
ware to begin data reception, and cleared by the
peripheral after a byte is received. After a byte is
received, the device may take up to 80 TCY to clear
RCEN and 800 TCY during emulation.
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions typically
is long enough for the RCEN bit to clear. For mul-
tiple byte receptions, the software must wait until
the bit is cleared by the peripheral before the next
byte can be received.
Date Codes that pertain to this issue:
All engineering and production devices.
34. Module: ECCP (PWM Mode)
When
the
PWM
auto-shutdown
feature
is
configured for automatic restart by setting the
PxRSEN bit (ECCPxDEL<7>), the pulse may
terminate immediately in a shutdown event. In
addition, the pulse may restart within the period if
the shutdown condition expires. This may result in
the generation of short pulses on the PWM
output(s).
Work around
Configure the auto-shutdown for software restart
by clearing the PxRSEN bit. The PWM can be re-
enabled
by
clearing
the
ECCPxASE
bit
(ECCPxAS<7>) after the shutdown condition
expires.
Date Codes that pertain to this issue:
All engineering and production devices.
35. Module: ECCP (PWM Mode)
When configured for half-bridge operation with
dead band (CCPxCON<7:6> = 10), the PWM out-
put may be corrupted for certain values of the
PWM duty cycle. This can occur when these
additional criteria are also met:
a non-zero, dead-band delay is specified
(PxDC6:PxDC0 > 0); and
the duty cycle has a value of 0 through 3, or
4n + 3 (n
≥ 1).
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
36. Module: CCP (PWM Mode)
Timer4 is not available as a clock source for either
CCP4
or
CCP5
in
any
PWM
mode
(CCPxCON<3:2> = 11). Selecting Timer4 as the
module’s clock source may cause the PWM output
to stop generating pulses.
Work around
To use CCP4 or CCP5 in PWM mode, use only
Timer2 as the clock source (T3CON<6,3> = 00).
Date Codes that pertain to this issue:
All engineering and production devices.
相关PDF资料 |
PDF描述 |
|---|---|
| DG613DY-E3 | IC SWITCH QUAD NO/NC 16-SOIC |
| PIC24EP256GU814-E/PH | IC MCU 16BIT 256KB FLASH 144TQFP |
| DSPIC33EP256MU814-E/PH | IC DSC 16BIT 256KB FLASH 144TQFP |
| DG612DY-E3 | IC SWITCH QUAD SPST 16-SOIC |
| PIC16C76-10I/SO | IC MCU OTP 8KX14 A/D PWM 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18LF8723-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF8723T-I/PT | 功能描述:8位微控制器 -MCU 128KB Flash 4KB RAM 1024 DataEE 12B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF96J65-I/PT | 功能描述:IC PIC MCU FLASH 48KX16 100TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 18F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP |
| PIC1-R68-JT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
发布紧急采购，3分钟左右您将得到回复。