- 您现在的位置：买卖IC网 > PDF目录15245 > RPA1A331MCN1GS (Nichicon)CAP ALUM 330UF 10V 20% SMD PDF资料下载
参数资料
| 型号： | RPA1A331MCN1GS |
| 厂商： | Nichicon |
| 文件页数： | 5/60页 |
| 文件大小： | 0K |
| 描述： | CAP ALUM 330UF 10V 20% SMD |
| 标准包装： | 1 |
| 系列： | PA |
| 电容： | 330µF |
| 额定电压： | 10V |
| 容差： | ±20% |
| 寿命@温度： | 105°C 时为 2000 小时 |
| 工作温度： | -55°C ~ 105°C |
| 特点： | 聚合物 |
| 纹波电流： | 3.6A |
| ESR（等效串联电阻）： | 20 毫欧 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 径向，Can - SMD |
| 尺寸/尺寸： | 0.394" 直径（10.00mm） |
| 高度 - 座高（最大）： | 0.315"（8.00mm） |
| 表面贴装占地面积： | 0.406" L x 0.406" W（10.30mm x 10.30mm） |
| 包装： | 标准包装 |
| 其它名称： | 493-6643-6 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Precautions
2. Mounting precautions
(1) Things to know before mounting
a) Do not reuse the FPCAP that has already been assembled in a device and energized.
Excluding the FPCAP that has been removed for measuring electrical characteristics during a periodic inspection,
they cannot be reused.
b) Leakage current may increase if the part has been stored for a long period of time.
In this case, use after voltage treatment under the rated voltage.
(2) Mounting-1
a) Mount after checking the capacitance and the rated voltage.
b) Mount after checking the polarity.
c) Do not drop on the floor and do not use parts that have been dropped.
d) Do not deform and then mount.
(3) Mounting-2
a) Mount after checking the match between the lead pitch and the PC board holes pitch.
b) When an automatic insertion equipment is used to clinch the lead wires, make sure it is set correctly.
c) Be careful of the shock force that can be produced by the automatic insertion equipment.
d) Do not apply excessive external force to the lead wires, the FPCAP itself, or the electrode terminals.
(4) Soldering with a soldering iron
a) Set the soldering conditions (temperature, time) so that they fall within the range stipulated by the catalog specification.
b) When the lead wire terminal must be processed because the terminal spacing and the PC board holes spacing do not match,
process it before soldering so that no stress is applied to the FPCAP itself.
c) Do not subject the FPCAP itself to excessive stress when soldering with a soldering iron.
d) When a soldering iron is used to repair the FPCAP that has already been soldered once and needs to be removed,
do it after the solder has been completely melted so that no stress is applied to the FPCAP terminals.
e) Do not let the tip of the soldering iron touch the FPCAP itself.
f ) The amount of leakage current after soldering may increase a slightly (from a few μ A to several hundred μ A) depending
on the soldering condition (preheating and solder temperature and time, PC board material and thickness, etc.)
The leakage current can be reduced by applying voltage.
(5) Flow soldering (Radial lead type)
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP.
e) Flow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
(6) Reflow soldering (SMD type)
Do not use reflow soldering for Radial lead type (Through Hole).
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP .
e) Reflow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
f) Do not use VPS (Vapor Phase Soldering).
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
3
相关PDF资料 |
PDF描述 |
|---|---|
| GCM43DCST | CONN EDGECARD 86POS DIP .156 SLD |
| GCM43DCMT | CONN EDGECARD 86POS .156 WW |
| GCA43DTKT | CONN EDGECARD 86POS DIP .125 SLD |
| EBM40DTBT | CONN EDGECARD 80POS R/A .156 SLD |
| EBM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RPA1C221MCN1GS | 功能描述:铝有机聚合物电容器 220UF 16V 20% RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel |
| RPA1C390MCN1GS | 功能描述:铝有机聚合物电容器 16V 39uF 20% Tol. RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel |
| RPA200H-11012SRUW/P | 功能描述:DC DC CONVERTER 12V 200W 制造商:recom power 系列:RPA200H 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:16.8V 电压 - 输入（最大值）:137.5V 电压 - 输出 1:12V 电压 - 输出 2:- 电压 - 输出 3:- 电压 - 输出 4:- 电流 - 输出（最大值）:17A 功率（W）:200W 电压 - 隔离:4.2kV 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，UVLO 工作温度:-40°C ~ 93.5°C（有降额） 效率:90% 安装类型:通孔 封装/外壳:10-DIP 模块 大小/尺寸:2.48" 长 x 2.39" 宽 x 0.51" 高（63.1mm x 60.6mm x 13.0mm） 供应商器件封装:- 控制特性:使能，高电平有效 标准包装:5 |
| RPA200H-11024SRUW/P | 功能描述:DC DC CONVERTER 24V 200W 制造商:recom power 系列:RPA200H 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:16.8V 电压 - 输入（最大值）:137.5V 电压 - 输出 1:24V 电压 - 输出 2:- 电压 - 输出 3:- 电压 - 输出 4:- 电流 - 输出（最大值）:8.5A 功率（W）:200W 电压 - 隔离:4.2kV 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，UVLO 工作温度:-40°C ~ 93.5°C（有降额） 效率:88% 安装类型:通孔 封装/外壳:10-DIP 模块 大小/尺寸:2.48" 长 x 2.39" 宽 x 0.51" 高（63.1mm x 60.6mm x 13.0mm） 供应商器件封装:- 控制特性:使能，高电平有效 标准包装:5 |
| RPA20-2405SAW/P | 功能描述:Isolated Module DC DC Converter 1 Output 5V 4A 9V - 36V Input 制造商:recom power 系列:RPA20-AW 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:9V 电压 - 输入（最大值）:36V 电压 - 输出 1:5V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:4A 功率（W） - 制造系列:20W 电压 - 隔离:1.6kV（1600V） 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:通孔 封装/外壳:6-DIP 模块 大小/尺寸:1.00" 长 x 1.00" 宽 x 0.40" 高（25.4mm x 25.4mm x 10.2mm） 工作温度:- 效率:88% 功率（W） - 最大值:20W 标准包装:10 |
发布紧急采购，3分钟左右您将得到回复。