- 您现在的位置：买卖IC网 > PDF目录15245 > RPA1A331MCN1GS (Nichicon)CAP ALUM 330UF 10V 20% SMD PDF资料下载
参数资料
| 型号： | RPA1A331MCN1GS |
| 厂商： | Nichicon |
| 文件页数： | 6/60页 |
| 文件大小： | 0K |
| 描述： | CAP ALUM 330UF 10V 20% SMD |
| 标准包装： | 1 |
| 系列： | PA |
| 电容： | 330µF |
| 额定电压： | 10V |
| 容差： | ±20% |
| 寿命@温度： | 105°C 时为 2000 小时 |
| 工作温度： | -55°C ~ 105°C |
| 特点： | 聚合物 |
| 纹波电流： | 3.6A |
| ESR（等效串联电阻）： | 20 毫欧 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 径向，Can - SMD |
| 尺寸/尺寸： | 0.394" 直径（10.00mm） |
| 高度 - 座高（最大）： | 0.315"（8.00mm） |
| 表面贴装占地面积： | 0.406" L x 0.406" W（10.30mm x 10.30mm） |
| 包装： | 标准包装 |
| 其它名称： | 493-6643-6 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Precautions
(7) Handling after soldering
a) Do not tilt, bend or twist the FPCAP after it has been soldered on the PC board.
b) Do not use the FPCAP as a handle to move the PC board after it has been attached to it.
c) Do not bump the FPCAP with objects after it has been soldered to the PC board. Make sure the FPCAP does not touch
other PC boards or components.
d) Do not subject to excessive stress after it has been soldered to the PC board.
(8) Washing the PC board
Check the following items before washing the PC board with these detergents; high quality alcohol-based cleaning fluid such as
Pine- α ST-100S, Clean-thru 750H, 750L, 750K, or Techno Care FRW14 through 17; or detergents including substitute
Freon such as AK-225AES and IPA.
a) Use immersion or ultrasonic wave to clean for a total of less than five minutes.
b) The temperature of the cleaning fluid should be less than 60 ° C.
c) Watch for contamination of the detergent (conductivity, pH, specific gravity, water content, etc.).
d) After cleaning do not store in a location subject to gases from the cleaning fluid or in an airtight container.
Dry the PC board and the FPCAP using hot air (less than the maximum operating temperature).
e) Please contact our company for details about detergents and cleaning methods, and about detergents other than those
listed above.
(9) Fixatives and coatings
a) Select appropriate material for the FPCAP marking material and sealant.
In particular, make sure the fixative, coating and thinner do not contain acetone or toluene.
b) Before applying a fixative or coating, completely remove any flux residue and foreign matter from the area where the PC board
and the FPCAP are to be joined together.
c) Allow any detergent to dry before applying the fixative or coating.
d) Please contact our company for fixative and coating heat curing conditions.
3. Precautions with completed board
(1) Do not directly touch the FPCAP terminals.
(2) Do not use electric conductors to cause a short circuit between the FPCAP terminals.
Do not subject the FPCAP to conductive solutions.
(3) Check the installation environment of the board on which the FPCAP is mounted.
(4) Aging of the completed board, please use the voltage below the rated voltage of the capacitor.
(5) It is recommended that the board be used at room temperature and in ordinary humidity.
For details, refer to the Operating Precaution Guidelines for the EIAJ RCR-2367C. (Safety Application Guide for fixed
aluminum electrolytic capacitors for use in electronic equipment.)
No part of this publication shall be reproduced without prior written permission of the publisher.
4. If trouble should occur
(1) In the event that a short circuit causes the current to become relatively small (Radial lead type : less than approximately
3A for φ 10 and less than approximately 1A for φ 6.3), the FPCAP itself will generate some heat, but the appearance
will not be affected even when electricity is supplied continuously. However, if there is a short circuit and the current value
exceeds the above mentioned values, the temperature inside the FPCAP will increase.
When the temperature exceeds approximately 200 ° C the internal pressure will increase, and an odorous gas will be released.
In this case, do not allow contact with your face and hands.
(2) If a short circuit occurs and an odorous gas is released, either turn off the device’s main power or unplug the power cord from
the outlet.
(3) If a short circuit should occur, it may take anywhere from a few seconds to a few minutes until an odorous gas develops,
depending on the conditions. Design the device so that a power protection circuit works during this time period.
4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
相关PDF资料 |
PDF描述 |
|---|---|
| GCM43DCST | CONN EDGECARD 86POS DIP .156 SLD |
| GCM43DCMT | CONN EDGECARD 86POS .156 WW |
| GCA43DTKT | CONN EDGECARD 86POS DIP .125 SLD |
| EBM40DTBT | CONN EDGECARD 80POS R/A .156 SLD |
| EBM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RPA1C221MCN1GS | 功能描述:铝有机聚合物电容器 220UF 16V 20% RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel |
| RPA1C390MCN1GS | 功能描述:铝有机聚合物电容器 16V 39uF 20% Tol. RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel |
| RPA200H-11012SRUW/P | 功能描述:DC DC CONVERTER 12V 200W 制造商:recom power 系列:RPA200H 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:16.8V 电压 - 输入（最大值）:137.5V 电压 - 输出 1:12V 电压 - 输出 2:- 电压 - 输出 3:- 电压 - 输出 4:- 电流 - 输出（最大值）:17A 功率（W）:200W 电压 - 隔离:4.2kV 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，UVLO 工作温度:-40°C ~ 93.5°C（有降额） 效率:90% 安装类型:通孔 封装/外壳:10-DIP 模块 大小/尺寸:2.48" 长 x 2.39" 宽 x 0.51" 高（63.1mm x 60.6mm x 13.0mm） 供应商器件封装:- 控制特性:使能，高电平有效 标准包装:5 |
| RPA200H-11024SRUW/P | 功能描述:DC DC CONVERTER 24V 200W 制造商:recom power 系列:RPA200H 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:16.8V 电压 - 输入（最大值）:137.5V 电压 - 输出 1:24V 电压 - 输出 2:- 电压 - 输出 3:- 电压 - 输出 4:- 电流 - 输出（最大值）:8.5A 功率（W）:200W 电压 - 隔离:4.2kV 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，UVLO 工作温度:-40°C ~ 93.5°C（有降额） 效率:88% 安装类型:通孔 封装/外壳:10-DIP 模块 大小/尺寸:2.48" 长 x 2.39" 宽 x 0.51" 高（63.1mm x 60.6mm x 13.0mm） 供应商器件封装:- 控制特性:使能，高电平有效 标准包装:5 |
| RPA20-2405SAW/P | 功能描述:Isolated Module DC DC Converter 1 Output 5V 4A 9V - 36V Input 制造商:recom power 系列:RPA20-AW 包装:管件 零件状态:在售 类型:隔离模块 输出数:1 电压 - 输入（最小值）:9V 电压 - 输入（最大值）:36V 电压 - 输出 1:5V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:4A 功率（W） - 制造系列:20W 电压 - 隔离:1.6kV（1600V） 应用:ITE（商业），铁路 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:通孔 封装/外壳:6-DIP 模块 大小/尺寸:1.00" 长 x 1.00" 宽 x 0.40" 高（25.4mm x 25.4mm x 10.2mm） 工作温度:- 效率:88% 功率（W） - 最大值:20W 标准包装:10 |
发布紧急采购，3分钟左右您将得到回复。