- 您现在的位置：买卖IC网 > PDF目录18777 > RXM-900-HP3-SPS (Linx Technologies Inc)RECEIVER RF 902-928MHZ 8P/100S PDF资料下载
参数资料
| 型号： | RXM-900-HP3-SPS |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 4/13页 |
| 文件大小： | 0K |
| 描述： | RECEIVER RF 902-928MHZ 8P/100S |
| 产品变化通告： | Internal Component Change 25/Aug/2011 |
| 标准包装： | 10 |
| 系列： | HP3 |
| 频率： | 902MHz ~ 928MHz |
| 灵敏度： | -100dBm |
| 数据传输率 - 最大： | 56 kbps |
| 调制或协议： | FM，FSK |
| 应用： | 家庭/工业自动化，远程访问，安全警报 |
| 电流 - 接收： | 18mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 多通道，模拟和数字数据 |
| 电源电压： | 2.8 V ~ 13 V |
| 工作温度： | -30°C ~ 85°C |
| 封装/外壳： | 18-SMD 模块 |
| 供应商设备封装： | 18-SIP |
| 包装： | 管件 |
| 其它名称： | Q3400415 |
THEORY OF OPERATION
POWER-UP SEQUENCE
The HP3 is a high-performance multi-channel, dual-conversion superhet
receiver capable of recovering both analog (FM) and digital (FSK) information
from a matching HP Series transmitter. FM / FSK modulation offers significant
advantages over AM or OOK modulation methods, including increased noise
As previously mentioned, the HP3 is controlled
by an on-board microprocessor. When power
is applied, the microprocessor executes the
receiver start-up sequence, after which the
POWER ON
Squelch Data
Output Pin
immunity and the receiver’s ability to capture in the presence of multiple signals.
receiver is ready to receive valid data.
Parallel Mode
Determine Mode
Serial Mode
This is especially helpful in crowded bands, like that in which the HP3 operates.
The adjacent figure shows the start-up
Read Channel
Selection Inputs
Program Freq. Synth
To Default CH. 50
{
Channel
Select
MODE
CS0
CS1
CS2
4MHz
Int. Osc.
VCO
PLL
34.7M
24MHz
Crystal
10.7MHz
BPF
IF
Amp
Quad
RSSI
Digital
Data
Analog
Data
sequence. This sequence is executed when
power is applied to the V CC line or when the
PDN line is taken high.
On power-up, the microprocessor reads the
external channel selection lines and sets the
frequency synthesizer to the appropriate
channel. Once the frequency synthesizer has
Program Frequency
Synthesizer
Crystal Oscillator
Begins to Work
Determine Squelch
State Data Output Pin
Crystal Oscillator
Begins to Operate
Ready for
Serial Data Input
Determine Squelch
State Data Output Pin
SAW BPF
BPF
LNA
stabilized, the receiver is ready to accept data.
Cycle Here Until
Channel
or Mode Change
Cycle Here Until More
Data Input
or Mode Change
Figure 9: HP3 Series Receiver Block Diagram
10.7M
BPF
Limiter
10.7M
Discriminator
POWER SUPPLY
Figure 10: Start-Up Sequence
The single-ended RF port is matched to 50-ohms to support commonly available
antennas, such as those manufactured by Linx. The RF signal coming in from
The HP3 incorporates a precision, low-dropout
regulator on-board, which allows operation over an
Vcc TO
MODULE
the antenna is filtered by a Surface Acoustic Wave (SAW) filter to attenuate
unwanted RF energy. A SAW filter provides significantly higher performance
than other filter types, such as an LC bandpass filter.
Once filtered, the signal is amplified by a Low Noise Amplifier (LNA) to increase
input voltage range of 2.8 to 13 volts DC. Despite this
regulator, it is still important to provide a supply that
is free of noise. Power supply noise can significantly
affect the receiver sensitivity; therefore, providing a
Vcc IN
10 Ω
10 μ F
A 10 Ω resistor in series with the supply followed by a
the receiver sensitivity and lower the overall noise figure of the receiver. After the
LNA, the signal is mixed with a synthesized local oscillator operating 34.7MHz
below the incoming transmission frequency to produce the first Intermediate
Frequency (IF).
The second conversion and FM demodulation is achieved by a high-
performance IF strip that mixes the 34.7MHz first conversion frequency with
24.0MHz from a precision crystal oscillator. The resulting second IF of 10.7MHz
is then highly amplified in preparation for demodulation.
A quadrature demodulator is used to recover the baseband signal from the
carrier. The demodulated waveform is filtered, after which it closely resembles
the original signal. The signal is routed to the analog output pin and the data
slicer stage, which provides squared digital output via the data output pin. A key
feature of the HP3 is the transparency of its digital output, which does not impose
balancing or duty-cycle requirements within a range of 100bps to 56kbps.
An on-board microcontroller manages receiver functions and greatly simplifies
user interface. The microcontroller reads the channel selection lines and
programs the on-board synthesizer. This frees the designer from complex
programming requirements and allows for manual or software channel selection.
The microcontroller also monitors incoming signal strength and squelches the
data output when the signal is not strong enough for accurate data detection.
Page 6
clean power supply for the module should be a high
priority during design.
Figure 11: Supply Filter
10μF tantalum capacitor from V CC to ground will help in cases where the quality
of supply power is poor. This filter should be placed close to the module’s supply
lines. These values may need to be adjusted depending on the noise present on
the supply line.
USING THE PDN PIN
The Power Down (PDN) line can be used to power down the receiver without the
need for an external switch. This line has an internal pull-up, so when it is held
high or simply left floating, the module will be active.
When the PDN line is pulled to ground, the receiver will enter into a low-current
(<10μA) power-down mode. During this time the receiver is off and cannot
perform any function. It may be useful to note that the startup time coming out
of power-down will be slightly less than when applying V CC .
The PDN line allows easy control of the receiver state from external
components, like a microcontroller. By periodically activating the receiver,
checking for data, then powering down, the receiver’s average current
consumption can be greatly reduced, saving power in battery-operated
applications.
Page 7
相关PDF资料 |
PDF描述 |
|---|---|
| M50100SB1600 | MODULE POWER 100A 1600V BRIDGE |
| M50100TB400 | MODULE POWER 100A 400V 3PH BRDG |
| M5060TB1600 | MODULE POWER 60A 1600V 3PH BRDG |
| EKMB1301113K | SENSOR PIR STD TYPE 6UA |
| M50100SB1000 | MODULE POWER 100A 1000V BRIDGE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RXM-916-ES | 功能描述:射频模块 RF Receiver 916MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| RXM-916-ES_ | 功能描述:RECEIVER RF 916MHZ 16PIN SMD RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| RX-MFR-RNLK-00 | 功能描述:KIT EVAL S4100 MULTI-FUNC READER RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667 |
| RXM-GNSS-GM-B | 制造商:Linx Technologies Inc 功能描述:GNSS RX MODULE GM SERIES 制造商:Linx Technologies Inc 功能描述:GM Series Global 3 - 4.3 V SMT -161 db 57.6 kbit/s GNSS Receiver Module 制造商:Linx Technologies Inc 功能描述:GPS Modules GM Series Receiver GNSS Module Bulk 制造商:LINX TECHNOLOGIES 功能描述:GM Series Global 3 - 4.3 V SMT -161 db 57.6 kbit/s GNSS Receiver Module |
| RXM-GNSS-GM-T | 制造商:Linx Technologies Inc 功能描述:GNSS RX MODULE GM SERIES |
发布紧急采购，3分钟左右您将得到回复。