- 您现在的位置：买卖IC网 > PDF目录18777 > RXM-900-HP3-SPS (Linx Technologies Inc)RECEIVER RF 902-928MHZ 8P/100S PDF资料下载
参数资料
| 型号： | RXM-900-HP3-SPS |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | RECEIVER RF 902-928MHZ 8P/100S |
| 产品变化通告： | Internal Component Change 25/Aug/2011 |
| 标准包装： | 10 |
| 系列： | HP3 |
| 频率： | 902MHz ~ 928MHz |
| 灵敏度： | -100dBm |
| 数据传输率 - 最大： | 56 kbps |
| 调制或协议： | FM，FSK |
| 应用： | 家庭/工业自动化，远程访问，安全警报 |
| 电流 - 接收： | 18mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 多通道，模拟和数字数据 |
| 电源电压： | 2.8 V ~ 13 V |
| 工作温度： | -30°C ~ 85°C |
| 封装/外壳： | 18-SMD 模块 |
| 供应商设备封装： | 18-SIP |
| 包装： | 管件 |
| 其它名称： | Q3400415 |
BOARD LAYOUT GUIDELINES
If you are at all familiar with RF devices, you may be concerned about
specialized board layout requirements. Fortunately, because of the care taken by
Linx in designing the modules, integrating them is very straightforward. Despite
this ease of application, it is still necessary to maintain respect for the RF stage
and exercise appropriate care in layout and application in order to maximize
performance and ensure reliable operation. The antenna can also be influenced
by layout choices. Please review this data guide in its entirety prior to beginning
your design. By adhering to good layout principles and observing some basic
design rules, you will be on the path to RF success.
MICROSTRIP DETAILS
A transmission line is a medium whereby RF energy is transferred from one
place to another with minimal loss. This is a critical factor, especially in high-
frequency products like Linx RF modules, because the trace leading to the
module’s antenna can effectively contribute to the length of the antenna,
changing its resonant bandwidth. In order to minimize loss and detuning, some
form of transmission line between the antenna and the module should be used,
unless the antenna can be placed very close (<1/8in.) to the module. One
common form of transmission line is a coax cable, another is the microstrip. This
term refers to a PCB trace running over a ground plane that is designed to serve
The adjacent figure shows the suggested
PCB footprint for the module. The actual pad
dimensions are shown in the Pad Layout
section of this manual. A ground plane (as
large as possible) should be placed on a
lower layer of your PC board opposite the
module. This ground plane can also be critical
to the performance of your antenna, which will
be discussed later. There should not be any
ground or traces under the module on the
same layer as the module, just bare PCB.
GROUND PLANE
ON LOWER LAYER
Figure 16: Suggested PCB Layout
as a transmission line between the module and the antenna. The width is based
on the desired characteristic impedance of the line, the thickness of the PCB,
and the dielectric constant of the board material. For standard 0.062in thick FR-
4 board material, the trace width would be 111 mils. The correct trace width can
be calculated for other widths and materials using the information below. Handy
software for calculating microstrip lines is also available on the Linx website,
www.linxtechnologies.com.
Trace
During prototyping, the module should be soldered to a properly laid-out circuit
board. The use of prototyping or “perf” boards will result in horrible performance
and is strongly discouraged.
No conductive items should be placed within 0.15in of the module’s top or sides.
Do not route PCB traces directly under the module. The underside of the module
has numerous signal-bearing traces and vias that could short or couple to traces
on the product’s circuit board.
The module’s ground lines should each have their own via to the ground plane
and be as short as possible.
AM / OOK receivers are particularly subject to noise. The module should, as
much as reasonably possible, be isolated from other components on your PCB,
especially high-frequency circuitry such as crystal oscillators, switching power
supplies, and high-speed bus lines. Make sure internal wiring is routed away
from the module and antenna, and is secured to prevent displacement.
The power supply filter should be placed close to the module’s V CC line.
In some instances, a designer may wish to encapsulate or “pot” the product.
Many Linx customers have done this successfully; however, there are a wide
variety of potting compounds with varying dielectric properties. Since such
compounds can considerably impact RF performance, it is the responsibility of
the designer to carefully evaluate and qualify the impact and suitability of such
Figure 17: Microstrip Formulas
Board
Ground plane
materials.
The trace from the module to the antenna should be kept as short as possible.
Dielectric Constant Width/Height (W/d)
Effective Dielectric
Constant
Characteristic
Impedance
A simple trace is suitable for runs up to 1/8-inch for antennas with wide
bandwidth characteristics. For longer runs or to avoid detuning narrow bandwidth
antennas, such as a helical, use a 50-ohm coax or 50-ohm microstrip
transmission line as described in the following section.
4.80
4.00
2.55
1.8
2.0
3.0
3.59
3.07
2.12
50.0
51.0
48.0
Page 14
Page 15
相关PDF资料 |
PDF描述 |
|---|---|
| M50100SB1600 | MODULE POWER 100A 1600V BRIDGE |
| M50100TB400 | MODULE POWER 100A 400V 3PH BRDG |
| M5060TB1600 | MODULE POWER 60A 1600V 3PH BRDG |
| EKMB1301113K | SENSOR PIR STD TYPE 6UA |
| M50100SB1000 | MODULE POWER 100A 1000V BRIDGE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RXM-916-ES | 功能描述:射频模块 RF Receiver 916MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| RXM-916-ES_ | 功能描述:RECEIVER RF 916MHZ 16PIN SMD RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| RX-MFR-RNLK-00 | 功能描述:KIT EVAL S4100 MULTI-FUNC READER RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667 |
| RXM-GNSS-GM-B | 制造商:Linx Technologies Inc 功能描述:GNSS RX MODULE GM SERIES 制造商:Linx Technologies Inc 功能描述:GM Series Global 3 - 4.3 V SMT -161 db 57.6 kbit/s GNSS Receiver Module 制造商:Linx Technologies Inc 功能描述:GPS Modules GM Series Receiver GNSS Module Bulk 制造商:LINX TECHNOLOGIES 功能描述:GM Series Global 3 - 4.3 V SMT -161 db 57.6 kbit/s GNSS Receiver Module |
| RXM-GNSS-GM-T | 制造商:Linx Technologies Inc 功能描述:GNSS RX MODULE GM SERIES |
发布紧急采购，3分钟左右您将得到回复。