- 您现在的位置：买卖IC网 > Datasheet目录505 > RXM-GPS-SR-T (Linx Technologies Inc)GPS MODULE SMD SIRF W/ANT Datasheet资料下载
参数资料
| 型号： | RXM-GPS-SR-T |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | GPS MODULE SMD SIRF W/ANT |
| 产品变化通告： | RXM-GPS-SR Receiver Change 21/Apr/2010 |
| 标准包装： | 250 |
| 系列： | SR |
| 封装/外壳： | 模块 |
| 供应商设备封装： | 模块 |
| 包装： | 散装 |
PROTOCOLS
LINX GPS modules use the SiRFstar III chipset. This chipset allows two
protocols to be used, NMEA-01 83 and SiRF Binary. Switching between the two
is handled using a single serial command. The NMEA protocol uses ASCII
characters for the input and output messages and provides the most common
features of GPS development in a small command set. The SiRF Binary protocol
uses BYTE data types and allows more detailed control over the GPS receiver
and its functionality using a much larger command set. Although both protocols
NMEA OUTPUT MESSAGES
The following sections outline the data structures of the various NMEA protocols
that are supported by the module. By default, the NMEA commands are output
at 9,600bps, 8 data bits, no parity, and 1 stop bit.
GGA – Global Positioning System Fixed Data
The table below contains the values for the following example:
$GPGGA,05 3 740.000,250 3 .6 3 19,N,121 3 6.0099,E,1,0 8 ,1.1,6 3 . 8 ,M,15.2,M,,0000*64
have selectable baud rates, it’s recommended that SiRF Binary use baud rates
of 38 ,400bps or higher. For a detailed description of the SiRF Binary protocol,
see the SiRF Binary Protocol Reference Manual, available from SiRF
Technology, Inc. Although SiRF Binary protocol may be used with the module,
Linx only offers tech support for the NMEA protocol.
INTERFACING WITH NMEA MESSAGES
Linx modules default to the NMEA protocol. Output messages are sent from the
receiver on the TX pin and input messages are sent to the receiver on the RX
pin. By default, output messages are sent once every second. Details of each
message are described in the following sections.
The NMEA message format is as follows: <Message-ID + Data Payload +
Checksum + End Sequence>. The serial data structure defaults to 9,600bps, 8
data bits, 1 stop bit, and no parity bits. Each message starts with a $ character
and ends with a <CR> <LF>. All fields within each message are separated by a
comma. The checksum follows the * character and is the last two characters, not
including the <CR> <LF>. It consists of two hex digits representing the exclusive
or (XOR) of all characters between, but not including, the $ and * characters.
When reading NMEA output messages, if a field has no value assigned to it, the
comma will still be placed following the previous comma. For example,
Name
Message ID
UTC Time
Latitude
N/S indicator
Longitude
E/W Indicator
Position Fix Indicator
Satellites Used
HDOP
MSL Altitude
Units
Geoid Separation
Units
Example
$GPGGA
05 3 740
250 3 .6 3 19
N
121 3 6.0099
E
1
0 8
1.1
6 3 . 8
M
15.2
M
Units
meters
meters
meters
meters
Description
GGA protocol header
hhmmss.sss
ddmm.mmmm
N=north or S=south
dddmm.mmmm
E=east or W=west
See Table 4
Range 0 to 12
Horizontal Dilution of Precision
{,04,,,,,2.0,} shows four empty fields between values 04 and 2.0. When writing
NMEA input messages, all fields are required, none are optional. An empty field
will invalidate the message and it will be ignored.
Reading NMEA output messages:
? Initialize a serial interface to match the serial data structure of the GPS receiver.
Age of Diff. Corr.
Diff. Ref. Station
Checksum
<CR> <LF>
ID 0000
*64
second Null fields when DGPS is not used
End of message termination
? Read the NMEA data from the TX pin into a receive buffer.
? Separate it into six buffers, one for each message type. Use the characters ($)
Table 2: Global Positioning System Fixed Data Example
and <CR> <LF> as end points for each message.
? For each message, calculate the checksum as mentioned above to compare
with the checksum received.
? Parse the data from each message using commas as field separators.
? Update the application with the parsed field values.
? Clear the receive buffer and be ready for the next set of NMEA messages.
Writing NMEA input messages:
Value
0
1
2
3 -5
6
Description
Fix not available or invalid
GPS SPS Mode, fix valid
Differential GPS, SPS Mode, fix valid
Not supported
Dead Reckoning Mode, fix valid
? Initialize a serial interface to match the serial data structure of the GPS receiver.
? Assemble the message to be sent with the calculated checksum.
? Transmit the message to the receiver on the RX pin.
Page 8
Table 3 : Position Indicator Values
Page 9
相关PDF资料 |
PDF描述 |
|---|---|
| RZE002P02TL | MOSFET P-CH 20V 200MA EMT3 |
| RZF020P01TL | MOSFET P-CH 12V 2A TUMT3 |
| RZF030P01TL | MOSFET P-CH 12V 3A TUMT3 |
| RZM002P02T2L | MOSFET P-CH 20V 0.2A UMT6 |
| RZQ045P01TR | MOSFET P-CH 12V 4.5A TSMT6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RXM-UHF | 制造商:RADIOMETRIX 制造商全称:RADIOMETRIX 功能描述:UHF Radio Telemetry Receiver Module |
| RXP0005 | 制造商:Panasonic Industrial Company 功能描述:ARM |
| RXP0014 | 制造商:Panasonic Industrial Company 功能描述:PULLEY |
| RXP0015 | 制造商:Panasonic Industrial Company 功能描述:ROLLER |
| RXP0016 | 制造商:Panasonic Industrial Company 功能描述:ROLLER |
发布紧急采购，3分钟左右您将得到回复。