- 您现在的位置：买卖IC网 > PDF目录192297 > S29GL032M10TAIR40 (SPANSION LLC) CAP 1.0UF 500V 10% X7R RAD-.475 .570X.500 CONF BULK PDF资料下载
参数资料
| 型号： | S29GL032M10TAIR40 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | CAP 1.0UF 500V 10% X7R RAD-.475 .570X.500 CONF BULK |
| 中文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PDSO48 |
| 封装： | MO-142EC, TSOP-48 |
| 文件页数： | 76/116页 |
| 文件大小： | 6024K |
| 代理商： | S29GL032M10TAIR40 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页
60
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B8 February 7, 2007
Data
Sheet
Command Definitions
Writing specific address and data commands or sequences into the command register initiates
incorrect address and data values or writing them in the improper sequence may place the device
in an unknown state. A reset command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is
latched on the rising edge of WE# or CE#, whichever happens first. See AC Characteristics for
timing diagrams.
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are
required to retrieve data. The device is ready to read array data after completing an Embedded
Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the erase-suspend-read
mode, after which the system can read data from any non-erase-suspended sector. After com-
pleting a programming operation in the Erase Suspend mode, the system may once again read
array data with the same exception. See Erase Suspend/Erase Resume Commands for more
information.
The system must issue the reset command to return the device to the read (or erase-suspend-
read) mode if DQ5 goes high during an active program or erase operation, or if the device is in
the autoselect mode. See the next section, Reset Command, for more information.
See also Requirements for Reading Array Data in the Device Bus Operations section for more in-
formation. The Read-Only Operations–AC Characteristics provides the read parameters, and
Figure 13 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address
bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to the read mode. Once erasure begins, however,
the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command se-
quence before programming begins. This resets the device to the read mode. If the program
command sequence is written while the device is in the Erase Suspend mode, writing the reset
command returns the device to the erase-suspend-read mode. Once programming begins, how-
ever, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command se-
quence. Once in the autoselect mode, the reset command must be written to return to the read
mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the
device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write
the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL032M10TAIR43 | CAP TANT 220UF 2.5V 20% POLY SMD |
| S29GL032M10FBCR33 | MirrorBit Flash Family |
| S29GL032M10FAIR50 | MirrorBit Flash Family |
| S29GL032M10FAIR52 | MirrorBit Flash Family |
| S29GL032M10FAIR53 | MirrorBit Flash Family |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL032M10TAIR42 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 32MBIT 4MX8/2MX16 100NS 48TSOP - Tape and Reel |
| S29GL032M10TAIR43 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR50 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR52 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
| S29GL032M10TAIR53 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:MirrorBit Flash Family |
发布紧急采购，3分钟左右您将得到回复。