- 您现在的位置：买卖IC网 > PDF目录69331 > SAB-XC164CM-8F40F (INFINEON TECHNOLOGIES AG) 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | SAB-XC164CM-8F40F |
| 厂商： | INFINEON TECHNOLOGIES AG |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | PLASTIC, TQFP-64 |
| 文件页数： | 50/69页 |
| 文件大小： | 1591K |
| 代理商： | SAB-XC164CM-8F40F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
XC164CM
Derivatives
Electrical Parameters
Data Sheet
52
V1.2, 2006-03
XTAL1 input current
I
IL
CC –
±20
A0 V < V
IN < VDDI
Pin capacitance11)
(digital inputs/outputs)
C
IO
CC –
10
pF
–
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications, also refer to the specification of the overload current
IOV.
2) This parameter is tested for P3, P9.
3) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
Table 12, Current Limits for Port Output Drivers. The limit for pin groups must be respected.
4) As a rule, with decreasing output current the output levels approach the respective supply level (
VOL → VSS,
VOH → VDDP). However, only the levels for nominal output currents are guaranteed.
5) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
6) An additional error current (
IINJ) will flow if an overload current flows through an adjacent pin. Please refer to
the definition of the overload coupling factor
KOV.
7) The driver of P3.15 is designed for faster switching, because this pin can deliver the system clock (CLKOUT).
The maximum leakage current for P3.15 is, therefore, increased to 1
A.
8) During a hardware reset this specification is valid for configuration on P1H.4, P1H.5, P9.4 and P9.5.
After a hardware reset this specification is valid for NMI.
9) The maximum current may be drawn while the respective signal line remains inactive.
10) The minimum current must be drawn to drive the respective signal line active.
11) Not subject to production test - verified by design/characterization.
Table 12
Current Limits for Port Output Drivers
Port Output Driver
Mode
Maximum Output Current
(
I
OLmax, -IOHmax)
1)
1) An output current above |
IOXnom| may be drawn from up to three pins at the same time.
For any group of 16 neighboring port output pins the total output current in each direction (
ΣI
OL and Σ-IOH) must
remain below 50 mA.
Nominal Output Current
(
I
OLnom, -IOHnom)
Strong driver
10 mA
2.5 mA
Medium driver
4.0 mA
1.0 mA
Weak driver
0.5 mA
0.1 mA
Table 11
DC Characteristics (Operating Conditions apply)1) (cont’d)
Parameter
Symbol
Limit Values
Unit Test Condition
Min.
Max.
相关PDF资料 |
PDF描述 |
|---|---|
| SAB-XC164CM-4F40F | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| SAB-XC164CM-8F20F | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| SAB-XC164KM-4F40F | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| SAB-XC164KM-4F20F | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| SAK-XC164KM-4F40F | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SAB-XC167CI-16F20F | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bi t Single-Chip Microcontroller Preliminary |
| SAB-XC167CI-16F40F | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bi t Single-Chip Microcontroller Preliminary |
| SAC | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Low Capacitance Transient Voltage Suppressor Diodes |
| SAC 8250 | 制造商:Edsyn International 功能描述:Bulk |
| SAC+0107 | 制造商:AIM Metals & Alloys LP 功能描述:Solder Bar-2.5lbs. 制造商:AIM PRODUCTS LLC. 功能描述:Solder Bar-2.5lbs. |
发布紧急采购，3分钟左右您将得到回复。