参数资料
型号: SC16C2550BIBS,151
厂商: NXP Semiconductors
文件页数: 24/31页
文件大小: 0K
描述: IC UART DUAL W/FIFO 32-HVQFN
产品培训模块: Stand-Alone UARTs
标准包装: 490
特点: 故障启动位检测
通道数: 2,DUART
FIFO's: 16 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-HVQFN(5x5)
包装: 托盘
产品目录页面: 828 (CN2011-ZH PDF)
其它名称: 568-3259
935280309151
SC16C2550BIBS-S
41
2570N–AVR–05/11
ATmega325/3250/645/6450
11. System Control and Reset
11.1
Resetting the AVR
During reset, all I/O Registers are set to their initial values, and the program starts execution
from the Reset Vector. The instruction placed at the Reset Vector must be a JMP – Absolute
Jump – instruction to the reset handling routine. If the program never enables an interrupt
source, the Interrupt Vectors are not used, and regular program code can be placed at these
locations. This is also the case if the Reset Vector is in the Application section while the Interrupt
Vectors are in the Boot section or vice versa. The circuit diagram in Figure 11-1 on page 42
shows the reset logic. Table 28-4 on page 301 defines the electrical parameters of the reset
circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes
active. This does not require any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal
reset. This allows the power to reach a stable level before normal operation starts. The time-out
period of the delay counter is defined by the user through the SUT and CKSEL Fuses. The dif-
ferent selections for the delay period are presented in “Clock Sources” on page 27.
11.2
Reset Sources
The Atmel ATmega325/3250/645/6450 has five sources of reset:
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset
threshold (V
POT).
External Reset. The MCU is reset when a low level is present on the RESET pin for longer
than the minimum pulse length.
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the
Watchdog is enabled.
Brown-out Reset. The MCU is reset when the supply voltage V
CC is below the Brown-out
Reset threshold (V
BOT) and the Brown-out Detector is enabled.
JTAG AVR Reset. The MCU is reset as long as there is a logic one in the Reset Register,
one of the scan chains of the JTAG system. Refer to the section “IEEE 1149.1 (JTAG)
相关PDF资料
PDF描述
SC16C752BIBS,151 IC UART DUAL W/FIFO 32-HVQFN
SC16C752BIBS,128 IC DUAL UART 64BYTE 32HVQFN
SC16C554BIB80,528 IC UART QUAD W/FIFO 80-LQFP
ATMEGA88-15AZ MCU AVR 8K FLASH 15MHZ 32-TQFP
SC16C752BIB48,151 IC DUAL UART 64BYTE 48LQFP
相关代理商/技术参数
参数描述
SC16C2550BIBS-F 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C2550BIN40 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C2550BIN40,112 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C2550IA44 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder
SC16C2550IA44,512 功能描述:UART 接口集成电路 16C 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel