参数资料
型号: SC16C550BIB48,128
厂商: NXP Semiconductors
文件页数: 16/48页
文件大小: 0K
描述: IC UART SINGLE W/FIFO 48-LQFP
标准包装: 2,000
特点: 可编程
通道数: 1,UART
FIFO's: 16 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 48-LQFP
供应商设备封装: 48-LQFP(7x7)
包装: 带卷 (TR)
其它名称: 935274388128
SC16C550BIB48-F
SC16C550BIB48-F-ND
SC16C550B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 1 October 2008
23 of 48
NXP Semiconductors
SC16C550B
5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by writing the
appropriate bits in this register.
Table 15.
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7]
Divisor latch enable. The internal baud rate counter latch and Enhance
Feature mode enable.
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch and enhanced feature register enabled
6
LCR[6]
Set break. When enabled, the Break control bit causes a break condition to
be transmitted (the TX output is forced to a logic 0 state). This condition exists
until disabled by setting LCR[6] to a logic 0.
logic 0 = no TX break condition (normal default condition)
logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the
remote receiver to a line break condition
5
LCR[5]
Set parity. If the parity bit is enabled, LCR[5] selects the forced parity format.
Programs the parity conditions (see Table 16).
logic 0 = parity is not forced (normal default condition)
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1 for
the transmit and receive data
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0 for
the transmit and receive data
4
LCR[4]
Even parity. If the parity bit is enabled with LCR[3] set to a logic 1, LCR[4]
selects the even or odd parity format.
logic 0 = odd parity is generated by forcing an odd number of logic 1s in the
transmitted data. The receiver must be programmed to check the same
format (normal default condition).
logic 1 = even parity is generated by forcing an even number of logic 1s in
the transmitted data. The receiver must be programmed to check the same
format.
3
LCR[3]
Parity enable. Parity or no parity can be selected via this bit.
logic 0 = no parity (normal default condition)
logic 1 = a parity bit is generated during the transmission, receiver checks
the data and parity for transmission errors
2
LCR[2]
Stop bits. The length of stop bit is specied by this bit in conjunction with the
programmed word length (see Table 17).
logic 0 or cleared = default condition
1:0
LCR[1:0]
Word length bits [1:0]. These two bits specify the word length to be
transmitted or received (see Table 18).
logic 0 or cleared = default condition
相关PDF资料
PDF描述
FT232HQ-REEL IC HS USB TO UART/FIFO 48QFN
FT232RQ-REEL IC USB FS SERIAL UART 32-QFN
SC16C550BIA44,512 IC UART SINGLE W/FIFO 44-PLCC
SC16C550BIA44,518 IC UART SINGLE W/FIFO 44-PLCC
SC16IS750IPW,128 IC UART I2C/SPI 24-TSSOP
相关代理商/技术参数
参数描述
SC16C550BIB48-S 功能描述:UART 接口集成电路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C550BIBS 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C550BIBS,128 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C550BIBS,151 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C550BIBS,157 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel