参数资料
| 型号： | SC16C752IB48,128 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 8/47页 |
| 文件大小： | 0K |
| 描述： | IC DUAL UART 64BYTE 48LQFP |
| 标准包装： | 1 |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 电源电压： | 2.5V，3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 标准包装 |
| 其它名称： | 568-5955-6 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
Philips Semiconductors
SC16C752
Dual UART with 64-byte FIFO
Product data
Rev. 04 — 20 June 2003
16 of 47
9397 750 11635
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.8 Break and time-out conditions
An RX idle condition is detected when the receiver line, RX, has been HIGH for
4 character time. The receiver line is sampled midway through each bit.
When a break condition occurs, the TX line is pulled LOW. A break condition is
activated by setting LCR[6].
6.9 Programmable baud rate generator
The SC16C752 UART contains a programmable baud generator that takes any clock
input and divides it by a divisor in the range between 1 and (216
1). An additional
divide-by-4 prescaler is also available and can be selected by MCR[7], as shown in
Figure 11. The output frequency of the baud rate generator is 16
× the baud rate. The
formula for the divisor is:
Where:
prescaler = 1, when MCR[7] is set to 0 after reset (divide-by-1 clock selected)
prescaler = 4, when MCR[7] is set to 1 after reset (divide-by-4 clock selected).
Remark: The default value of prescaler after reset is divide-by-1.
Figure 11 shows the internal prescaler and baud rate generator circuitry.
DLL and DLH must be written to in order to program the baud rate. DLL and DLH are
the least signicant and most signicant byte of the baud rate divisor. If DLL and DLH
are both zero, the UART is effectively disabled, as no baud clock will be generated.
Remark: The programmable baud rate generator is provided to select both the
transmit and receive clock rates.
frequency 1.8432 MHz and 3.072 MHz, respectively.
Figure 12 shows the crystal clock circuit reference.
Fig 11. Prescaler and baud rate generator block diagram.
divisor
XTAL1 crystal input frequency
prescaler
---------------------------------------------------------------------------
desired baud rate
16
×
()
---------------------------------------------------------------------------------
=
BAUD RATE
GENERATOR
LOGIC
MCR[7] = 1
MCR[7] = 0
PRESCALER
LOGIC
(DIVIDE-BY-1)
INTERNAL
OSCILLATOR
LOGIC
002aaa233
XTAL1
XTAL2
INPUT CLOCK
PRESCALER
LOGIC
(DIVIDE-BY-4)
REFERENCE
CLOCK
INTERNAL
BAUD RATE
CLOCK FOR
TRANSMITTER
AND
RECEIVER
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C754BIB80,557 | IC UART QUAD W/FIFO 80-LQFP |
| SC16C850IBS/Q900,5 | IC UART SGL UNIV ASYNC 36-VFQFN |
| SC16C852VIET,151 | IC UART DUAL W/FIFO 36TFBGA |
| SC16IS741IPW,112 | IC UART 16TSSOP |
| SC16IS750IBS,151 | IC UART I2C/SPI 24-HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C754 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO |
| SC16C754B | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC16C754BIA68 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C754BIA68,512 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C754BIA68,518 | 功能描述:UART 接口集成电路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。