参数资料
型号: SC16IS762IBS,151
厂商: NXP Semiconductors
文件页数: 19/60页
文件大小: 0K
描述: IC UART DUAL I2C/SPI 32-HVQFN
产品培训模块: Bridge Solutions
Stand-Alone UARTs
I²C Bus Fundamentals
特色产品: NXP - I2C Interface
标准包装: 490
特点: 低电流
通道数: 2,DUART
FIFO's: 64 字节
规程: RS232,RS485
电源电压: 2.5V, 3.3V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-HVQFN(5x5)
包装: 托盘
产品目录页面: 828 (CN2011-ZH PDF)
配用: 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART
568-3510-ND - DEMO BOARD SPI/I2C TO UART
其它名称: 568-2240
935279293151
SC16IS762IBS-S
SC16IS752_SC16IS762
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 9 — 22 March 2012
26 of 60
NXP Semiconductors
SC16IS752; SC16IS762
Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
8.7 Modem Control Register (MCR)
The MCR controls the interface with the mode, data set, or peripheral device that is
emulating the modem. Table 19 shows Modem Control Register bit settings.
[1]
MCR[7:5] and MCR[2] can only be modified when EFR[4] is set, that is, EFR[4] is a write enable.
Table 19.
Modem Control Register bits description
Bit
Symbol
Description
7
Clock divisor.
logic 0 = divide-by-1 clock input
logic 1 = divide-by-4 clock input
6
IrDA mode enable.
logic 0 = normal UART mode
logic 1 = IrDA mode
5
Xon Any.
logic 0 = disable Xon Any function
logic 1 = enable Xon Any function
4
MCR[4]
Enable loopback.
logic 0 = normal operating mode
logic 1 = enable local Loopback mode (internal). In this mode the
MCR[1:0] signals are looped back into MSR[4:5] and the TX output is
looped back to the RX input internally.
3
MCR[3]
reserved
2
MCR[2]
TCR and TLR enable.
logic 0 = disable the TCR and TLR register
logic 1 = enable the TCR and TLR register
1
MCR[1]
RTS
logic 0 = force RTS output to inactive (HIGH)
logic 1 = force RTS output to active (LOW). In Loopback mode,
controls MSR[4]. If Auto-RTS is enabled, the RTS output is controlled
by hardware flow control.
0
MCR[0]
DTR. If GPIO5 or GPIO1 is selected as DTR modem pin through
IOControl register bit 1 or bit 2, the state of DTR pin can be controlled as
below. Writing to IOState bit 5 or bit 1 will not have any effect on the DTR
pin.
logic 0 = force DTR output to inactive (HIGH)
logic 1 = force DTR output to active (LOW)
相关PDF资料
PDF描述
SC26C92A1N,112 IC UART 40-DIP
SC28C94A1A,512 IC UART QUAD W/FIFO 52-PLCC
SC28L198A1A,512 IC UART OCTAL W/FIFO 84-PLCC
SC28L91A1B,557 IC UART SINGLE W/FIFO 44-PQFP
SC28L92A1B,557 IC UART DUAL W/FIFO 44-PQFP
相关代理商/技术参数
参数描述
SC16IS762IBS-F 功能描述:UART 接口集成电路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16IS762IBS-T 功能描述:IC UART DUAL I2C/SPI 32-HVQFN RoHS:是 类别:集成电路 (IC) >> 接口 - UART(通用异步接收器/发送器) 系列:- 标准包装:250 系列:- 特点:* 通道数:2,DUART FIFO's:16 字节 规程:RS232,RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP(7x7) 包装:托盘 其它名称:XR16L2551IM-F-ND
SC16IS762IPW 功能描述:UART 接口集成电路 DUAL UART 64BYTE RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16IS762IPW,112 功能描述:UART 接口集成电路 DUAL UART 64BYTE RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16IS762IPW,128 功能描述:UART 接口集成电路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel