参数资料
| 型号： | SC174MLTRT |
| 厂商： | Semtech |
| 文件页数： | 16/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 4A 10MLPD |
| 产品培训模块： | Power Supplies 101 |
| 标准包装： | 1 |
| 系列： | EcoSpeed® |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.75 V ~ 5.23 V |
| 输入电压： | 3 V ~ 5.5 V |
| 频率 - 开关： | 200kHz ~ 1MHz |
| 电流 - 输出： | 4A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 10-MLPD（3x3） |
| 其它名称： | SC174MLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
SC174
ESR MAX =
V RIPPLE 40 mV
T ON_VINMAX =
= 227ns
L =
= 0.51 m H
× I RIPPLEMAX ) 2
L × (I OUT +
COUT MIN =
T ON_VINMIN =
= 277ns
I RIPPLE =
I RIPPLE_VIN MIN =
= 0.485A
× 0.511A) 2
2 m H × (4A +
COUT MIN =
= 353 m F
ApplicationsInformation(continued)
Example
In this example, the inductor ripple current is set equal to
50% of the maximum load current. Therefore ripple cur-
rent will be 50% x 4A or 2A. To find the minimum induc-
tance needed, use the V IN and T ON values that correspond
to V INMAX .
1V
5.5V ? 800 kHz
(5.5V - 1V) ? 227ns
2A
A larger value of 2μH is selected. This will decrease the
maximum I RIPPLE to 0.511A.
Note that the inductor must be rated for the maximum
DC load current plus 1/2 of the ripple current.
The ripple current under minimum V IN conditions is also
checked using the following equations.
1V
4.5V × 800kHz
(V IN - V OUT ) × T ON
L
(4.5V - 1V) × 277ns
2 m H
Capacitor Selection
The output capacitors are chosen based on required ESR
and capacitance. The maximum ESR requirement is con-
trolled by the output ripple requirement and the DC tol-
erance. The output voltage has a DC value that is equal
to the valley of the output ripple plus 1/2 of the peak-
to-peak ripple. Change in the output ripple voltage will
lead to a change in DC voltage at the output.
The design goal is for the output voltage regulation to be
±4% under static conditions. The internal 750mV refer-
ence tolerance is 1%. Assuming a 1% tolerance from the
FB resistor divider, this allows 2% tolerance due to V OUT
ripple. Since this 2% error comes from 1/2 of the ripple
voltage, the allowable ripple is 4%, or 40mV for a 1V out-
put.
? 2010 Semtech Corporation
The maximum ripple current of 0.511A creates a ripple
voltage across the ESR. The maximum ESR value allowed
is shown by the following equations.
=
I RIPPLEMAX 0.51A
ESR MAX = 78.3 m?
The output capacitance is chosen to meet transient re-
quirements. A worst-case load release, from maximum
load to no load at the exact moment when inductor cur-
rent is at the peak, determines the required capacitance.
If the load release is instantaneous (load changes from
maximum to zero in < 1μs), the output capacitor must
absorb all the inductor’s stored energy. This will cause a
peak voltage on the capacitor according to the following
equation.
1
2
(V PEAK ) 2 - (V OUT ) 2
Assuming a peak voltage V PEAK of 1.050V (50mV rise upon
load release), and a 4A load release, the required capaci-
tance is shown by the next equation.
1
2
(1.05V) 2 - (1.0V) 2
If the load release is relatively slow, the output capacitance
can be reduced. At heavy loads during normal switching,
when the FB pin is above the 750mV reference, the DL
output is high and the low-side MOSFET is on. During this
time, the voltage across the inductor is approximately
-V OUT . This causes a down-slope or falling di/dt in the
inductor. If the load di/dt is not much faster than the
-di/dt in the inductor, then the inductor current will tend
to track the falling load current. This will reduce the
excess inductive energy that must be absorbed by the
output capacitor, therefore a smaller capacitance can be
used.
The following can be used to calculate the needed ca-
pacitance for a given dI LOAD /dt. Peak inductor current is
shown by the next equation.
16
相关PDF资料 |
PDF描述 |
|---|---|
| SC183CULTRT | IC REG BUCK SYNC ADJ 2A 16MLPQ |
| SC185HULTRT | IC REG BUCK SYNC 1.5V 4A 16MLPQ |
| SC186ULTRT | IC REG BUCK SYNC ADJ 4A 16MLPQ |
| SC189LULTRT | IC REG BUCK SYNC 1.8V 1.5A 6MLPD |
| SC190CIMLTRT | IC REG BUCK SYNC ADJ 0.3A 10MLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC175F | 制造商:LISTA 功能描述:SC Drawer, 6-1/16 Usable Ht, 440lb Cap. 制造商:Lista International Corp 功能描述:SC Drawer, 6-1/16 Usable Ht, 440lb Cap. |
| SC1766 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:BATTERY CHARGE CONTROLLER |
| SC1766CS08 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:BATTERY CHARGE CONTROLLER |
| SC1766CS14 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:BATTERY CHARGE CONTROLLER |
| SC177 | 制造商:TE Connectivity 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。