- 您现在的位置：买卖IC网 > PDF目录299883 > SC26C92A1N-S (NXP SEMICONDUCTORS) 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | SC26C92A1N-S |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, MO-015AJ, SOT-129-1, DIP-40 |
| 文件页数： | 27/31页 |
| 文件大小： | 221K |
| 代理商： | SC26C92A1N-S |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页
Philips Semiconductors
Product specification
SC26C92
Dual universal asynchronous receiver/transmitter (DUART)
2000 Jan 31
5
PIN DESCRIPTION
SYMBOL
PKG
PIN
NAME AND FUNCTION
SYMBOL
40,44
TYPE
NAME AND FUNCTION
D0-D7
X
I/O
Data Bus: Bidirectional 3-State data bus used to transfer commands, data and status between the DUART
and the CPU. D0 is the least significant bit.
CEN
X
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART are
enabled on D0-D7 as controlled by the WRN, RDN and A0-A3 inputs. When High, places the D0-D7 lines
in the 3-State condition.
WRN
X
I
Write Strobe: When Low and CEN is also Low, the contents of the data bus is loaded into the addressed
register. The transfer occurs on the rising edge of the signal.
RDN
X
I
Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be
presented on the data bus. The read cycle begins on the falling edge of RDN.
A0-A3
X
I
Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESET
X
I
Reset: A High level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0-OP7 in the
High state, stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA and
TxDB outputs in the mark (High) state. Sets MR pointer to MR1 and resets MR0.
INTRN
X
O
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the eight
maskable interrupting conditions are true. Requires a pullup resistor.
X1/CLK
X
I
Crystal 1: Crystal connection or an external clock input. A crystal of a clock the appropriate frequency
(nominally 3.6864 MHz) must be supplied at all times. For crystal connections see Figure 7, Clock Timing.
X2
X
I
Crystal 2: Crystal connection. See Figure 7. If a crystal is not used this pin must be left open or not driving
more than one TTL equivalent load.
RxDA
X
I
Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low.
RxDB
X
I
Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low.
TxDA
X
O
Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held
in the “mark” condition when the transmitter is disabled, idle or when operating in local loopback mode.
“Mark” is High, “space” is Low.
TxDB
X
O
Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output is
held in the ‘mark’ condition when the transmitter is disabled, idle, or when operating in local loopback mode.
‘Mark’ is High, ‘space’ is Low.
OP0
X
O
Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be
deactivated automatically on receive or transmit.
OP1
X
O
Output 1: General purpose output or Channel B request to send (RTSBN, active-Low). Can be
deactivated automatically on receive or transmit.
OP2
X
O
Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A receiver
1X clock output.
OP3
X
O
Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B transmitter
1X clock output, or Channel B receiver 1X clock output.
OP4
X
O
Output 4: General purpose output or Channel A open-drain, active-Low, RxA interrupt ISR[1] output.
OP5
X
O
Output 5: General purpose output or Channel B open-drain, active-Low, RxB interrupt ISR[5] output.
OP6
X
O
Output 6: General purpose output or Channel A open-drain, active-Low, TxA interrupt ISR[0] output.
OP7
X
O
Output 7: General purpose output, or Channel B open-drain, active-Low, TxB interrupt ISR[4] output.
IP0
X
I
Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN). Pin has an internal
VCC pull-up device supplying 1 to 4 mA of current.
IP1
X
I
Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN). Pin has an internal
VCC pull-up device supplying 1 to 4 mA of current.
IP2
X
I
Input 2: General purpose input or counter/timer external clock input. Pin has an internal VCC pull-up device
supplying 1 to 4
mA of current.
IP3
X
I
Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the external
clock is used by the transmitter, the transmitted data is clocked on the falling edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP4
X
I
Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP5
X
I
Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the external
clock is used by the transmitter, the transmitted data is clocked on the falling edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP6
X
I
Input 6: General purpose input or Channel B receiver external clock input (RxCB). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
VCC
X
I
Power Supply: +5V supply input.
GND
X
I
Ground
相关PDF资料 |
PDF描述 |
|---|---|
| SC2982CSK-5.0T | 5 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
| SC3031B | SAW OSCILLATOR, 390 MHz |
| SC321-2-TE12LA | 1 A, 200 V, SILICON, SIGNAL DIODE |
| SC48-04406-2 | 48 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, WIRE WRAP |
| SC48-04406-88 | 48 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, WIRE WRAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC26C92C1A | 功能描述:UART 接口集成电路 UART DUAL W/FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC26C92C1A,512 | 功能描述:UART 接口集成电路 UART DUAL W/FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC26C92C1A,518 | 功能描述:UART 接口集成电路 5V 2 CH UART COM TEMP RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC26C92C1A,529 | 功能描述:UART 接口集成电路 5V 2CH UART COM TEMP RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC26C92C1A | 制造商:NXP Semiconductors 功能描述:CMOS DUAL UART SMD 26C92 PLCC44 |
发布紧急采购，3分钟左右您将得到回复。