- 您现在的位置：买卖IC网 > PDF目录11819 > SC28L198A1BE,528 (NXP Semiconductors)IC UART OCTAL SOT407-1 PDF资料下载
参数资料
| 型号： | SC28L198A1BE,528 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 11/57页 |
| 文件大小： | 0K |
| 描述： | IC UART OCTAL SOT407-1 |
| 标准包装： | 1,000 |
| 特点： | 故障启动位检测 |
| 通道数： | 8 |
| FIFO's： | 16 字节 |
| 电源电压： | 3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 带卷 (TR) |
| 其它名称： | 935262731528 SC28L198A1BE-T SC28L198A1BE-T-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
Philips Semiconductors
Product data sheet
SC28L198
Octal UART for 3.3 V and 5 V supply voltage
2006 Aug 10
19
Table 3. MR0– Mode Register 0
Bit 7
Bit 6
Bit 5:4
Bit 3:2
Bit 1:0
Xon/Xoff * transparency
Address Recognition *
transparency
TxiNT
In–band flow control mode
Address Recognition
control
0 – flow control characters
received are pushed onto
the
RxFIFO
1 – flow control characters
received are not pushed
onto the RxFIFO
0 – Address characters
received are pushed to
RxFIFO
1 – Address characters
received are not pushed
onto the RxFIFO
TxFIFO
interrupt
level
control
00 – empty
01 – 3/4 empty
10 – 1/2 empty
11 – not full
00 – host mode, only the host CPU
may initiate flow control actions
through the CR
01 – Auto Transmitter flow control
10 – Auto Receiver flow control
11 – Auto Receiver and Transmitter
flow control
00 – none
01 – Auto wake
10 – Auto doze
11 – Auto wake and
auto doze
* If these bits are not 0 the characters will be stripped regardless of
bits (3:2) or (1:0)
MR0[7:6] – Control the handling of recognized Xon/Xoff or Address
characters. If set, the character codes are placed on the RxFIFO
along with their status bits just as ordinary characters are. If the
character is not pushed onto the RxFIFO, its received status will be
lost unless the receiver is operating in the block error mode, see
MR1[5] and the general discussion on receiver error handling.
Interrupt processing is not effected by the setting of these bits. See
Character recognition section.
MR0[5:4] – Controls the fill level at which a transmitter begins to
present its interrupt number to the interrupt arbitration logic. Use of
a low fill level minimizes the number of interrupts generated and
maximizes the number of transmit characters per interrupt cycle. It
also increases the probability that the transmitter will go idle for lack
of characters in the TxFIFO.
MR0[3:2] – Controls the Xon/Xoff processing logic. Auto
Transmitter flow control allows the gating of Transmitter activity by
Xon/Xoff characters received by the Channel’s receiver. Auto
Receiver flow control causes the Transmitter to emit an Xoff
character when the RxFIFO has loaded to a depth of 12 characters.
Draining the RxFIFO to a level of 8 or less causes the Transmitter to
emit an Xon character. All transmissions require no host
involvement. A setting other than b’00 in this field precludes the use
of the command register to transmit Xon/Xoff characters.
Note: Interrupt generation in Xon/Xoff processing is controlled by the
IMR (Interrupt Mask Register) of the individual channels. The
interrupt may be cleared by a read of the XISR, the Xon/Xoff
Interrupt Status Register. Receipt of a flow control character will
always generate an interrupt if the IMR is so programmed. The
MR0[3:2] bits have effect on the automatic aspects of flow control
only, not the interrupt generation.
MR0[1:0] – This field controls the operation of the Address
recognition logic. If the device is not operating in the special or
“wake–up” mode, this hardware may be used as a general purpose
character detector by choosing any combination except b’00.
Interrupt generation is controlled by the channel IMR. The interrupt
may be cleared by a read of the XISR, the Xon/Xoff Interrupt Status
Register. See further description in the section on the Wake Up
mode.
Table 4. MR1 – Mode Register 1
Bit 7
Bit 6
Bit 5
Bit 4:3
Bit 2
Bit 1:0
RxRTS
Control
ISR Read Mode
Error Mode
Parity Mode
Parity Type
Bits per Charac-
ter
0 – off
1 – on
0 – ISR unmasked
1 – ISR masked
0 = Character
1 = Block
00 – With Parity
01 – Force parity
10 – No parity
11 – Special Mode
0 = Even
1 = Odd
00 – 5
01 – 6
10 – 7
11 – 8
MR1[7]: Receiver Request to Send Control
This bit controls the deactivation of the RTSN output (I/O2) by the
receiver. This output is asserted and negated by commands applied
via the command register. MR1[7] = 1 causes RTSN to be
automatically negated upon receipt of a valid start bit if the receiver
FIFO is
full or greater. RTSN is reasserted when an the FIFO fill
level falls below
full. This constitutes a change from previous
members of Philips (Signets)’ UART families where the RTSN
function triggered on FIFO full. This behavior caused problems with
PC UARTs that could not stop transmission at the proper time. .
The RTSN feature can be used to prevent overrun in the receiver, by
using the RTSN output signal, to control the CTSN input of the
transmitting device.
MR1[6]: Interrupt Status Masking
This bit controls the readout mode of the Interrupt Status Register,
ISR. If set, the ISR reads the current status masked by the IMR, i.e.
only interrupt sources enabled in the IMR can ever show a ’1’ in the
ISR. If cleared, the ISR shows the current status of the interrupt
source without regard to the Interrupt Mask setting.
MR1[5]: Error Mode Select
This bit selects the operating mode of the three FIFOed status bits
(FE, PE, received break). In the character mode, status is provided
on a character by character basis; the status applies only to the
character at. the bottom of the FIFO. In the block mode, the status
provided in the SR for these bits is the accumulation (logical OR) of
相关PDF资料 |
PDF描述 |
|---|---|
| V24B5H150BL3 | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150BL | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150B3 | CONVERTER MOD DC/DC 5V 150W |
| SCC2692AE1B44,551 | IC UART DUAL W/FIFO 44PLCC |
| SC16C754BIB80,551 | IC UART QUAD 64BYTE 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC28L198A1BE-S | 功能描述:UART 接口集成电路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L198C1A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Octal UART for 3.3V and 5V supply voltage |
| SC28L201 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:3.3 V, 5 V UART, 3.125 Mbit/s, with 256-byte FIFO |
| SC28L201A1DGG | 功能描述:UART 接口集成电路 3-5V 1CH UART 3MBPS 256B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L201A1DGG,112 | 功能描述:UART 接口集成电路 3-5V 1CH UART 3MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。